SIST EN 12644-1:2001+A1:2008

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Dvigala (žerjavi) - Navodilo za uporabo in preskus - 1. del: NavodilaKrane - Informationen für die Nutzung und Prüfung - Teil 1: BetriebsanleitungenAppareils de levage à charge suspendue - Information pour l'utilisation et les essais - Partie 1: InstructionsCranes - Information for use and testing - Part 1: Instructions53.020.20DvigalaCranesICS:Ta slovenski standard je istoveten z:EN 12644-1:2001+A1:2008SIST EN 12644-1:2001+A1:2008en,fr01-december-2008SIST EN 12644-1:2001+A1:2008SLOVENSKI
STANDARD



SIST EN 12644-1:2001+A1:2008



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12644-1:2001+A1
July 2008 ICS 53.020.20 Supersedes EN 12644-1:2001 English Version
Cranes - Information for use and testing - Part 1: Instructions
Appareils de levage à charge suspendue - Information pour l'utilisation et les essais - Partie 1: Instructions
Krane - Informationen für die Nutzung und Prüfung -Teil 1: Betriebsanleitungen This European Standard was approved by CEN on 13 December 2000 and includes Amendment 1 approved by CEN on 15 June 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12644-1:2001+A1:2008: ESIST EN 12644-1:2001+A1:2008



EN 12644-1:2001+A1:2008 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.4 2 Normative references.4 3 Terms and definitions.5 4 Hazards.6 5 Requirements for instructions.6 5.1 General.6 5.2 Crane Specification.6 5.2.1 General.6 5.2.2 Identification.6 5.3 User´s instructions.7 5.4 Crane driver´s instructions.8 5.4.1 General.8 5.4.2 Information.8 5.4.3 Checks before starting any lifting operation.8 5.4.4 Specific safety aspects during operation.8 5.4.5 Specific safety aspects before leaving the crane out-of-service.9 5.5 Maintenance instructions (preventative and corrective).9 6 Verification of the requirements.10 Annex ZA (informative)
!!!!Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC"""".11 Annex ZB (informative)
!!!!Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""".12 Bibliography.13
SIST EN 12644-1:2001+A1:2008



EN 12644-1:2001+A1:2008 (E) 3 Foreword This document (EN 12644-1:2001+A1:2008) has been prepared by Technical Committee CEN/TC 147 “Cranes - Safety”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2008-06-15. This document supersedes EN 12644-1:2001. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document." According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 12644-1:2001+A1:2008



EN 12644-1:2001+A1:2008 (E) 4 Introduction This European Standard is a type C-standard as defined in EN 414. This standard has been prepared to be a harmonized standard to provide one means of conforming with the essential health and safety requirements of the Machinery Directive, as amended. This is part 1 of a series intended to give information for use to be supplied by the manufacturers of cranes. The other part of this standard is: Part 2: Marking !deleted text" The extent to which hazards are covered is indicated in the scope of this standard. 1 Scope This part of EN 12644 specifies requirements for the presentation and content of instruction handbook(s) supplied by the manufacturer for the use of cranes. This crane standard has been written to be used in conjunction with other crane standards being prepared by CEN/TC 147. NOTE Specific requirements for particular types of crane, are given in the appropriate European Standard for the particular crane type. The hazards covered by this standard are identified in clause 4. This part of EN 12644 applies to cranes which are manufactured after the date of approval by CEN of this standard. This standard does not cover hazards related to the lifting of persons. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and publications are listed hereafter. For dated references, subsequent amendments to, or revisions of, any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 292-2:1991+ A1:1995, Safety of machinery – Basic concepts, general principles for design – Part 2: Technical principles and specifications EN 1070:1998, Safety of machinery - Terminology prEN 13001-1:1997, Crane safety - General design - Part 1: General principles and requirements SIST EN 12644-1:2001+A1:2008



EN 12644-1:2001+A1:2008 (E) 5 NOTE Informative annex ZA provides information regarding relevant EU directives, European and International Standards. 3 Terms and definitions For the purposes of this European Standard the terms and definitions given in EN 1070:1998 and the following apply. 3.1 check visual and functional assessment (not a test) of the condition of the crane without dismantling.
3.2 crane driver person operating the crane for the purpose of handling loads.
3.3 examination verification that the crane can safely continue in service including a functional test of all safety devices i.e. limiting, indicating equipment, brakes, clutches etc to verify that they operate within the required tolerances. An examination is more thorough than an inspection.
3.4 inspection looking at the crane for defects and checking the operation of the controls, limiting and indicating devices without loading the crane. This is much more than a check but does not normally require any part of the crane to be dismantled other than removal or opening of cover(s) or housing(s).
3.5 instruction handbook principal means by which the manufacturer provides information or instructions on how the crane has to be used.
3.6 rated capacity load(s) that the crane is designed to lift for a given operating condition (e.g. configuration, position of load).
3.7 service conditions
3.7.1 in-service crane in use handling or preparing to handle loads up to the rated capacity in conditions as specified by the manufacturer.
3.7.2 out-of-service crane out of use, without load and left in conditions as specified by the manufacturer.
3.8 test specific operation of the crane with or without a defined load in order to establish whether the crane is fit for use.
3.9 use any operation with or on the crane e.g. transportation, erection, dismantling, maintenance, movements of the load. SIST EN 12644-1:2001+A1:2008



EN 12644-1:2001+A1:2008 (E) 6
3.10 user; user organisation person or organisation which has direct control over the crane use.
4 Hazards Cranes can present hazards to persons in the danger zone. Instructions regarding use, handling, maintenance etc. of cranes are necessary to reduce or eliminate the risks associated with the hazards. This standard specifies requirements for instructions in order to prevent or minimize hazards or hazardous situations. A list of hazards is given in the appropriate standards for each crane type. 5 Requirements for instructio
...