SIST EN IEC 60793-1-32:2019

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lichtwellenleiter - Teil 1-32: Messmethoden und Prüfverfahren - Absetzbarkeit der Beschichtung
(IEC 60793-1-32:2018)Fibres optiques - Partie 1-32: Méthodes de mesure et procédures d'essai - Dénudabilité du revêtement
(IEC 60793-1-32:2018)Optical fibres - Part 1-32: Measurement methods and test procedures - Coating strippability (IEC 60793-1-32:2018)33.180.10Fibres and cablesICS:Ta slovenski standard je istoveten z:EN IEC 60793-1-32:2018SIST EN IEC 60793-1-32:2019en01-marec-2019SIST EN IEC 60793-1-32:2019SLOVENSKI
STANDARDSIST EN 60793-1-32:20101DGRPHãþD



SIST EN IEC 60793-1-32:2019



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN IEC 60793-1-32
December 2018 ICS 33.180.10
Supersedes
EN 60793-1-32:2010
English Version
Optical fibres - Part 1-32: Measurement methods and test procedures - Coating strippability (IEC 60793-1-32:2018)
Fibres optiques - Partie 1-32: Méthodes de mesure et procédures d'essai - Dénudabilité du revêtement (IEC 60793-1-32:2018)
Lichtwellenleiter - Teil 1-32: Messmethoden und Prüfverfahren - Absetzbarkeit der Beschichtung (IEC 60793-1-32:2018) This European Standard was approved by CENELEC on 2018-12-20. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23,
B-1040 Brussels © 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60793-1-32:2018 E SIST EN IEC 60793-1-32:2019



EN IEC 60793-1-32:2018 (E) 2 European foreword The text of document 86A/1890/FDIS, future edition 3 of IEC 60793-1-32, prepared by SC 86A "Fibres and cables" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 60793-1-32:2018. The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2019-09-21 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021-12-21
This document supersedes EN 60793-1-32:2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60793-1-32:2018 was approved by CENELEC as a European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60793-2-10 NOTE Harmonized as EN 60793-2-10 IEC 60793-2-20 NOTE Harmonized as EN 60793-2-20 IEC 60793-2-30 NOTE Harmonized as EN 60793-2-30 IEC 60793-2-50 NOTE Harmonized as EN 60793-2-50 IEC 60793-2-60 NOTE Harmonized as EN 60793-2-60
SIST EN IEC 60793-1-32:2019



EN IEC 60793-1-32:2018 (E) 3 Annex ZA (normative)
Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1
Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2
Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.
Publication Year Title EN/HD Year IEC 60793-1-1 - Optical fibres – Part 1-1: Measurement methods and test procedures – General and guidance EN 607933-1-1 -
SIST EN IEC 60793-1-32:2019



SIST EN IEC 60793-1-32:2019



IEC 60793-1-32 Edition 3.0 2018-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Optical fibres –
Part 1-32: Measurement methods and test procedures – Coating strippability
Fibres optiques –
Partie 1-32: Méthodes de mesure et procédures d’essai – Dénudabilité du revêtement
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 33.180.10
ISBN 978-2-8322-6293-1
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ®
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé. SIST EN IEC 60793-1-32:2019 colourinside



– 2 – IEC 60793-1-32:2018 © IEC 2018 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 5 4 Apparatus . 5 4.1 Tensile equipment. 5 4.2 Load cell . 6 4.3 Transducer amplifier . 6 4.4 Stripping tool . 6 4.5 Fibre guide . 7 5 Specimen preparation . 7 5.1 Representative sample . 7 5.2 Strip length . 7 6 Procedure . 8 6.1 General . 8 6.2 Stripping rate . 8 6.3 Preconditioning . 8 6.4 Calibrating the transducer amplifier . 8 6.5 Loading the test specimen . 8 6.6 Stripping the coating . 9 7 Calculations . 9 7.1 Calculation for the value of a specimen . 9 7.1.1 General . 9 7.1.2 Approach 1 – Average strip force . 9 7.1.3 Approach 2 – Peak strip force . 9 7.2 Calculation of the reported value. 9 8 Documentation . 9 8.1 Information to be presented . 9 8.2 Information to be available for each test. 10 9 Specification information . 10 Bibliography . 11
Figure 1 – Example of test arrangement . 6 Figure 2 – Length of fibre to be stripped . 8
SIST EN IEC 60793-1-32:2019



IEC 60793-1-32:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
OPTICAL FIBRES –
Part 1-32: Measurement methods and test procedures –
Coating strippability
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60793-1-32 has been prepared by subcommittee 86A: Fibres and cables, of IEC technical committee 86: Fibre optics. This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: expansion of the range of coating dimensions applicable to the procedure detailed in this document to accommodate optical fibres with a 200 µm coating dimension. SIST EN IEC 60793-1-3
...