Industrial electroheating equipment - Test methods for direct arc furnaces

This International Standard specifies test procedures, conditions and methods according to which the main parameters and the main operational characteristics of electric arc furnaces (EAF) operated either with alternating current (EAFac) or with direct current (EAFdc) with a capacity above 500 kg/heat are established. The EAF technology is also applicable to furnaces, in which liquid metal is kept at high temperature or superheated to casting temperature (e.g. in a ladle furnace (LF), operated with alternating current). Test methods for some special equipment, e.g. controlled rectifiers for EAFdc, are covered by IEC 60146-1-1. Test methods for submerged arc furnaces (SAF) are covered by IEC 60683.

Industrielle Elektrowärmeanlagen - Prüfverfahren für Lichtbogen-Schmelzöfen

Chauffage électrique industriel - Méthodes d'essai des fours à arc direct

La CEI 60676:2011 spécifie les procédures, les conditions et les méthodes d'essai suivant lesquelles sont établis les principaux paramètres et les principales caractéristiques de fonctionnement des fours à arc électrique (FAE), soit à courant alternatif (FAE c.a.), soit à courant continu (FAE c.c.), dont la capacité est supérieure à 500 kg/charge de fusion. Cette troisième édition annule et remplace la précédente édition parue en 2002 et constitue une révision technique. Les principales modifications techniques par rapport à l'édition précédente sont les suivantes:  - Article 1 (Domaine d'application et objet) - les types de fours sont définis de façon plus claire.  - L'Article 2 (Références normatives) et l'Article 3 (Termes et définitions) ont été mis à jour et complétés.  - Un nouvel Article 4 (Caractéristiques des fours à arc électrique (FAE)) a été ajouté; il se concentre principalement sur les essais nécessaires pour l'appareillage électrique à haute tension/haute intensité de l'installation.  - L'Article 5 (Type des essais et conditions générales d'exécution) et l'Article 6 (Essais techniques) ont été modifiés pour s'adapter aux exigences actuelles relatives à la sécurité de fonctionnement d'un four à arc électrique.

Oprema za industrijsko električno ogrevanje - Preskusne metode za peči z odkritim oblokom

Ta mednarodni standard določa preskusne postopke, pogoje in metode, po katerih so vzpostavljeni glavni parametri in glavne značilnosti peči z odkritim električnim oblokom (EAF), ki delujejo z izmeničnim tokom (EAFac) ali enosmernim tokom (EAFdc) z zmogljivostjo nad 500 kg/enoto toplote. Tehnologija EAF se uporablja tudi za peči, v katerih se tekoča kovina vzdržuje na visoki temperaturi ali segreje na temperaturo vlivanja (npr. v ponovčni peči (LF), ki deluje z izmeničnim tokom). Preskusne metode za nekatere vrste posebne opreme, npr. nadzorovane usmernike za EAFdc, so zajete v standardu IEC 60146-1-1. Preskusne metode za peči z zakritim oblokom (SAF) so zajete v standardu IEC 60683.

General Information

Status
Published
Publication Date
22-Mar-2012
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
20-Mar-2012
Due Date
25-May-2012
Completion Date
23-Mar-2012

Relations

Buy Standard

Standard
EN 60676:2012
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60676:2012
01-maj-2012
2SUHPD]DLQGXVWULMVNRHOHNWULþQRRJUHYDQMH3UHVNXVQHPHWRGH]DSHþL]
RGNULWLPREORNRP
Industrial electroheating equipment - Test methods for direct arc furnaces
Industrielle Elektrowärmeanlagen - Prüfverfahren für Lichtbogen-Schmelzöfen
Chauffage électrique industriel - Méthodes d'essai des fours à arc direct
Ta slovenski standard je istoveten z: EN 60676:2012
ICS:
25.180.10 (OHNWULþQHSHþL Electric furnaces
SIST EN 60676:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60676:2012

---------------------- Page: 2 ----------------------

SIST EN 60676:2012

EUROPEAN STANDARD
EN 60676

NORME EUROPÉENNE
February 2012
EUROPÄISCHE NORM

ICS 25.180.10 Supersedes EN 60676:2002


English version


Industrial electroheating equipment -
Test methods for direct arc furnaces
(IEC 60676:2011)


Chauffage électrique industriel -  Industrielle Elektrowärmeanlagen -
Méthodes d'essai des fours à arc direct Prüfverfahren für Lichtbogen-Schmelzöfen
(CEI 60676:2011) (IEC 60676:2011)





This European Standard was approved by CENELEC on 2011-12-13. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60676:2012 E

---------------------- Page: 3 ----------------------

SIST EN 60676:2012
EN 60676:2012 - 2 -

Foreword
The text of document 27/816/FDIS, future edition 3 of IEC 60676, prepared by IEC/TC 27 "Industrial
electroheating" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60676:2012.

The following dates are fixed:
(dop) 2012-09-13
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2014-12-13
standards conflicting with the
document have to be withdrawn

This document supersedes EN 60676:2002.
EN 60676:2012 includes the following significant technical changes with respect to EN 60676:2002:
– Clause 1 (Scope and object) – types of furnaces are more clearly defined.
– Clause 2 (Normative references) and Clause 3 (Terms and definitions) have been updated and
completed.
– New Clause 4 (Features of the EAFsystem) has been added; it mainly concentrates on the tests
necessary for high-voltage / high-current electrical equipment in the installation.
– Clause 5 (Type of tests and general conditions of their performance) and Clause 6 (Technical tests)
have been modified according to today’s requirements for safe operation of an EAF.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.

Endorsement notice
The text of the International Standard IEC 60676:2011 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
[2] IEC 60146-1-1:2009 NOTE  Harmonized as EN 60146-1-1:2010 (not modified).
[3] IEC 60683:2011 NOTE  Harmonized as EN 60683:2012 (not modified).

---------------------- Page: 4 ----------------------

SIST EN 60676:2012
- 3 - EN 60676:2012

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this docum
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.