Small craft - Seacocks and through-hull fittings (ISO 9093:2020)

This document specifies requirements for through-hull fittings, seacocks, hose connections, their
fittings and their installation in small craft with a length of hull, LH, as defined in ISO 8666:2020, of up
to 24 m.
This document is not applicable to engine and heater exhaust fittings, and sail drive through-hull
fittings.

Kleine Wasserfahrzeuge - Seeventile und Außenhautdurchführungen (ISO 9093:2020)

Dieses Dokument legt Anforderungen an Außenhautdurchführungen, Seeventile, Schlauchverbindungen, Schlauchstutzen und deren Einbau in kleine Wasserfahrzeuge mit einer Rumpflänge LH bis 24 m, wie in ISO 8666:2020 definiert, fest.
Dieses Dokument ist nicht anzuwenden für Motor- und Heizungsabgasleitungen und Außenhautdurch-führungen für Segelbootantriebe.

Petits navires - Vannes de coque et passe-coques (ISO 9093:2020)

Le présent document spécifie les exigences relatives aux passe-coques, vannes de coque, raccords de tuyaux flexibles, leur connexion et leur installation sur les petits navires d'une longueur de coque LH, telle que définis dans l'ISO 8666:2020, inférieure ou égale à 24 m.
Ce document n'est pas applicable aux raccords d'échappement de moteur et de chauffage, ni aux passe-coque des embases de transmission «sail drive».

Mala plovila - Ventili in fitingi za morsko vodo v trupu plovila (ISO 9093:2020)

General Information

Status
Published
Public Enquiry End Date
05-Sep-2019
Publication Date
04-Feb-2021
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
04-Feb-2021
Due Date
11-Apr-2021
Completion Date
05-Feb-2021

Relations

Buy Standard

Standard
EN ISO 9093:2021
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 9093:2019
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 9093:2021
01-marec-2021
Nadomešča:
SIST EN ISO 9093-1:2000
SIST EN ISO 9093-1:2018
SIST EN ISO 9093-2:2003
SIST EN ISO 9093-2:2018
Mala plovila - Ventili in fitingi za morsko vodo v trupu plovila (ISO 9093:2020)
Small craft - Seacocks and through-hull fittings (ISO 9093:2020)
Kleine Wasserfahrzeuge - Seeventile und Außenhautdurchführungen (ISO 9093:2020)
Petits navires - Vannes de coque et passe-coques (ISO 9093:2020)
Ta slovenski standard je istoveten z: EN ISO 9093:2021
ICS:
47.020.30 Sistemi cevi Piping systems
47.080 Čolni Small craft
SIST EN ISO 9093:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 9093:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 9093:2021


EN ISO 9093
EUROPEAN STANDARD

NORME EUROPÉENNE

January 2021
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 9093-1:1997, EN ISO 9093-1:2018,
EN ISO 9093-2:2002, EN ISO 9093-2:2018
English Version

Small craft - Seacocks and through-hull fittings (ISO
9093:2020)
Petits navires - Vannes de coque et passe-coques (ISO Kleine Wasserfahrzeuge - Seeventile und
9093:2020) Außenhautdurchführungen (ISO 9093:2020)
This European Standard was approved by CEN on 29 November 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9093:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 9093:2021
EN ISO 9093:2021 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4

2

---------------------- Page: 4 ----------------------
SIST EN ISO 9093:2021
EN ISO 9093:2021 (E)
European foreword
This document (EN ISO 9093:2021) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with Technical Committee CEN/TC 464 “Small Craft” the secretariat of which is
held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2021, and conflicting national standards shall be
withdrawn at the latest by July 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 9093-1:1997, EN ISO 9093-2:2002, EN ISO 9093-1:2018 and
EN ISO 9093-2:2018.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 9093:2020 has been approved by CEN as EN ISO 9093:2021 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 9093:2021
EN ISO 9093:2021 (E)
Annex ZA
(informative)

Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request
M/542/C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and
Annex I of Directive 2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) Remarks/Notes
Directive 2013/53/EU of this EN
Annex I, Clause 2.5, Owner’s In respect of information to be
Clause 11
manual included in the Owner’s Manual
This standard do not address
windows, portlights, doors and
Annex I, Clause 3.4, Openings in
Clause 3, 4, 5, 6, 7, 9 hatch covers and point loads
hull, deck and superstructure
applied by the weight of persons
on the deck.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.

4

---------------------- Page: 6 ----------------------
SIST EN ISO 9093:2021
INTERNATIONAL ISO
STANDARD 9093
First edition
2020-12
Small craft — Seacocks and through-
hull fittings
Petits navires — Vannes de coque et passe-coques
Reference number
ISO 9093:2020(E)
©
ISO 2020

---------------------- Page: 7 ----------------------
SIST EN ISO 9093:2021
ISO 9093:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 9093:2021
ISO 9093:2020(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material requirements . 2
4.1 General . 2
4.2 Material combinations . 2
4.3 Resistance to deterioration/corrosion tests . 2
4.4 Strength requirements . 3
4.5 Range of operating temperatures . 3
4.5.1 General operating requirements . 3
4.5.2 Storage temperature requirement . 3
4.5.3 High temperature operating test . 3
4.5.4 Low temperature operating test . 3
5 Through-hull fittings . 3
5.1 Thread identification . 3
5.2 General design requirements . 4
5.3 Detailed design requirements . . 4
5.3.1 Stem . 4
5.3.2 Flange diameter . 5
5.3.3 Finish. 5
6 Seacocks — Design requirements . 5
6.1 General . 5
6.2 Thread length requirements . 5
7 Hose fittings . 6
7.1 Design requirements . 6
7.2 Hose connection. 6
8 Water scoops and outboard water strainers . 7
9 Installation . 7
9.1 Hull reinforcements . 7
9.2 Installation requirements . 7
10 Device installation information . 8
11 Owner's manual . 8
Annex A (normative) Strength test . 9
Annex B (normative) Corrosion resistance test .10
Annex C (normative) UV stabilisation test .11
Bibliography .12
© ISO 2020 – All rights reserved iii

---------------------- Page: 9 ----------------------
SIST EN ISO 9093:2021
ISO 9093:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 188, Small craft, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 464, Small craft, in
accordance with the Agreement on technical cooperation bet
...

SLOVENSKI STANDARD
oSIST prEN ISO 9093:2019
01-september-2019
Mala plovila - Ventili in fitingi za morsko vodo v trupu plovila (ISO/DIS 9093:2019)
Small craft - Seacocks and through-hull fittings (ISO/DIS 9093:2019)
Kleine Wasserfahrzeuge - Seeventile und Außenhautdurchführungen (ISO/DIS
9093:2019)
Petits navires - Vannes de coque et passe-coques (ISO/DIS 9093:2019)
Ta slovenski standard je istoveten z: prEN ISO 9093
ICS:
47.020.30 Sistemi cevi Piping systems
47.080 Čolni Small craft
oSIST prEN ISO 9093:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 9093:2019

---------------------- Page: 2 ----------------------
oSIST prEN ISO 9093:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 9093
ISO/TC 188/SC 2 Secretariat: SIS
Voting begins on: Voting terminates on:
2019-06-14 2019-09-06
Small craft — Seacocks and through-hull fittings
ICS: 47.080
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 9093:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 9093:2019
ISO/DIS 9093:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 9093:2019
ISO/DIS 9093:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material requirements . 2
4.1 General . 2
4.2 Material combinations . 2
4.3 Resistance to deterioration/corrosion . 3
4.4 Mechanical properties . 3
4.5 Range of operating temperatures . 3
4.5.1 General operating requirements . 3
4.5.2 Storage temperature requirement . 3
4.5.3 High temperature operating test . 3
4.5.4 Low temperature operating test . 3
5 Through-hull fittings . 3
5.1 Thread identification . 3
5.2 General design requirements . 5
5.3 Detail design requirements . 5
5.3.1 Stem . 5
5.3.2 Flange diameter . 5
5.3.3 Finish. 5
6 Seacocks - Design requirements . 5
7 Hose fittings . 6
7.1 Design requirements . 6
7.2 Hose connection. 6
8 Water scoops and outboard water strainers . 7
9 Installation . 7
9.1 Hull reinforcements . 7
9.2 Installation requirements . 8
10 Device installation information . 8
11 Owner's manual . 8
11.1 Requirements for device information . 9
Annex A (normative) Strength Test .10
Annex B (normative) Corrosion Resistance Test .11
Annex C (normative) UV Stabilisation test .12
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered .13
© ISO 2019 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 9093:2019
ISO/DIS 9093:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 188, Small Craft, SC 2, Engines and
propulsion systems.
This first edition cancels and replaces the previous two part edition (ISO 9093-1:1994 and
ISO 9093-2:2002), which has been technically revised.
The main changes compared to the previous edition are as follows:
— the previous 2 parts have been combined into a single standard;
— the definition of corrosion resistance has changed;
— a test for UV stabilisation has been added;
— a test for corrosion resistance has been added;
— an installed strength test has been added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 9093:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 9093:2019(E)
Small craft — Seacocks and through-hull fittings
1 Scope
This document specifies requirements for through-hull fittings, seacocks, hose connection and fittings
used in small craft of up to 24 m length of hull.
This document is not applicable to engine and heater exhaust fittings, and sail drive through-hull
fittings.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 7-1, Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances
and designation
ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions,
tolerances and designation
ISO 6509:1981, Corrosion of metals and alloys — Determination of dezincification resistance of brass
ISO 527-1:2012, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2:2012, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 178:2010/Amd 1:2013, Plastics — Determination of flexural properties — Amendment 1
ISO 180, 1/Amd 2:2013, Plastics — Determination of Izod impact strength / Amendment 2: Precision data
ISO 8666:2016, Small craft — Principal data
ISO 6509-1:2014, Corrosion of metals and alloys — Determination of dezincification resistance of copper
alloys with zinc — Part 1: Test method
ISO 6509-2:2017, Corrosion of metals and alloys — Determination of dezincification resistance of copper
alloys with zinc — Part 2: Assessment criteria
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
through-hull fitting
fitting designed to permit passage of liquids including suspended solids or gases through the hull
© ISO 2019 – All rights reserved 1

---------------------- Page: 7 ----------------------
oSIST prEN ISO 9093:2019
ISO/DIS 9093:2019(E)

3.2
seacock
shut-off device intended to prevent the ingress of water normally directly fitted to a hull or a through-
hull fitting
3.3
readily accessible
capable of being reached quickly and safely for effective use under emergency conditions without the
use of tools
3.4
maximum load waterline
waterline of the craft when upright in the M condition according to ISO 8666
LDC
3.5
heeled waterline
the level of the water on the hull in the M condition according to ISO 8666 when the craft is inclined to
LDC
— 7° for motor boats and sailing multihu
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.