Small craft - Hull construction and scantlings - Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate (ISO 12215-1:2000)

This part of ISO 12215 is applicable to thermosetting resins and glass-fibre reinforcement used in the construction of
small craft with a length of the hull of up to , in accordance with ISO 8666. This part of ISO 12215 specifies
the minimum requirements for material properties of glass reinforcement and resin matrix and the reference laminate
made thereof.
This part of ISO 12215 may be applicable to materials other than those specified, provided that the minimum requirements
and properties of the reference laminate are met.
NOTE The underlying reason for preparing this International Standard is to harmonize existing standards and recommended
practices for loads on the hull and the dimensioning of small craft because they differ too considerably and thus limit general
worldwide acceptability of boats.

Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 1: Werkstoffe: Härtbare Harze, Verstärkungsfasern aus Textilglas, Referenzlaminat (ISO 12215-1:2000)

Petits navires - Construction de coques et échantillons - Partie 1: Matériaux: Résines thermodurcissables, renforcement de fibres de verre, stratifié de référence (ISO 12215-1:2000)

La présente partie de l'ISO 12215 s'applique aux résines thermodurcissables et aux renforcements de fibres de verre utilisés pour la construction des petits navires de longueur de coque (LH) allant jusqu'à 24 m, conformément à l'ISO 8666. Elle spécifie les exigences minimales concernant les propriétés des produits à base de fibre de verre, des matrices de résine et des stratifiés de référence élaborés à partir de ces produits.  La présente partie de l'ISO 12215 peut être appliquée à d'autres produits, sous réserve que les exigences minimales et les propriétés du stratifié de référence soient respectées.  
NOTE La présente Norme internationale a été élaborée en vue d'harmoniser les normes et pratiques recommandées existantes, relatives aux charges exercées sur la coque et au dimensionnement des petits navires, qui présentent des différences considérables, d'où une limitation de la conformité générale des navires à l'échelle mondiale.

Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 1. del: Materiali: toplotno obdelane smole, ojačitev s steklenimi vlakni, referenčni laminat (ISO 12215-1:2000)

Ta del standarda ISO 12215 se uporablja za toplotno obdelane smole in ojačitev s steklenimi vlakni, ki se uporabljajo pri izdelavi malih plovil z dolžino trupa do X m v skladu s standardom ISO 8666. Ta del standarda ISO 12215 določa minimalne zahteve za lastnosti materialov pri matrici ojačitve s steklenimi vlakni in smolo ter referenčnega laminata, izdelanega iz njih.
Ta del ISO 12215 se lahko uporablja tudi za druge materiale pod pogojem, da so izpolnjene minimalne zahteve in lastnosti referenčnega laminata.
OPOMBA: Osnovni razlog za pripravo tega mednarodnega standarda je uskladitev obstoječih standardov in priporočenih postopkov v zvezi z obremenitvami trupa ter dimenzioniranjem malih plovil, ker se preveč razlikujejo in tako omejujejo splošno sprejemljivost čolnov po vsem svetu.

General Information

Status
Published
Public Enquiry End Date
14-Mar-2018
Publication Date
28-Oct-2018
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
18-Oct-2018
Due Date
23-Dec-2018
Completion Date
29-Oct-2018

Relations

Buy Standard

Standard
EN ISO 12215-1:2018
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 12215-1:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 12215-1:2001
0DODSORYLOD.RQVWUXNFLMDWUXSDLQ]DKWHYDQHODVWQRVWLGHO0DWHULDOLWRSORWQR
REGHODQHVPROHRMDþLWHYVVWHNOHQLPLYODNQLUHIHUHQþQLODPLQDW ,62
Small craft - Hull construction and scantlings - Part 1: Materials: Thermosetting resins,
glass-fibre reinforcement, reference laminate (ISO 12215-1:2000)
Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 1: Werkstoffe:
Härtbare Harze, Verstärkungsfasern aus Textilglas, Referenzlaminat (ISO 12215-1:2000)
Petits navires - Construction de coques et échantillons - Partie 1: Matériaux: Résines
thermodurcissables, renforcement de fibres de verre, stratifié de référence (ISO 12215-
1:2000)
Ta slovenski standard je istoveten z: EN ISO 12215-1:2018
ICS:
47.020.10 Ladijski trupi in njihovi Hulls and their structure
konstrukcijski elementi elements
47.080 ýROQL Small craft
SIST EN ISO 12215-1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 12215-1:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 12215-1:2018


EN ISO 12215-1
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2018
EUROPÄISCHE NORM
ICS 47.080
English Version

Small craft - Hull construction and scantlings - Part 1:
Materials: Thermosetting resins, glass-fibre reinforcement,
reference laminate (ISO 12215-1:2000)
Petits navires - Construction de coques et échantillons - Kleine Wasserfahrzeuge - Rumpfbauweise und
Partie 1 : Matériaux : Résines thermodurcissables, Dimensionierung - Teil 1: Werkstoffe: Härtbare Harze,
renforcement de fibres de verre, stratifié de référence Verstärkungsfasern aus Textilglas, Referenzlaminat
(ISO 12215-1:2000) (ISO 12215-1:2000)
This European Standard was approved by CEN on 15 July 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12215-1:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 12215-1:2018
EN ISO 12215-1:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 12215-1:2018
EN ISO 12215-1:2018 (E)
European foreword
The text of ISO 12215-1:2000 has been prepared by Technical Committee ISO/TC 188 "Small craft” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 12215-
1:2018 by Technical Committee CEN/SS T01 “Shipbuilding and maritime structures” the secretariat of
which is held by CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12215-1:2000.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA or ZB, which is an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 12215-1:2000 has been approved by CEN as EN ISO 12215-1:2018 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 12215-1:2018
EN ISO 12215-1:2018 (E)
Annex ZA
(informative)

Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered

This European Standard has been prepared under a Commission’s standardization request
M/542/C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.

Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.

Table ZA.1— Correspondence between this European Standard and
Annex I of Directive 2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) of Remarks/Notes
Directive 2013/53/EU this EN
Annex 1.A.3.1 All clauses This standard supports the
selection and combination of
reinforcement fibres and resins
and the mechanical properties of
the reference laminate that shall
be achieved by any
manufacturing process for
construction of watercraft only.

WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.

4

---------------------- Page: 6 ----------------------

SIST EN ISO 12215-1:2018
INTERNATIONAL ISO
STANDARD 12215-1
First edition
2000-09-01
Small craft — Hull construction and
scantlings —
Part 1:
Materials: Thermosetting resins, glass-fibre
reinforcement, reference laminate
Petits navires — Construction de coques et échantillons —
Partie 1: Matériaux: Résines thermodurcissables, renforcement de fibres de
verre, stratifié de référence
Reference number
ISO 12215-1:2000(E)
© ISO 2000

---------------------- Page: 7 ----------------------

SIST EN ISO 12215-1:2018
ISO 12215-1:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec-
tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's mem-
ber body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2000 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 12215-1:2018
ISO 12215-1:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical com-
mittees. Each member body interested in a subject for which a technical committee has been established has the
right to be represented on that committee. International organizations, governmental and non-governmental, in liai-
son with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 12215 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 12215-1 was prepared by Technical Committee ISO/TC 188, Small craft.
ISO 12215 consists of the following parts, under the general title Small craft — Hull construction and scantlings:
— Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate
The following will be the subjects of future parts of ISO 12215:
— Part 2: Materials: Core materials for sandwich-construction, embedded materials
— Part 3: Materials: Steel, aluminium alloys, wood, other materials
— Part 4: Workshop and manufacturing
— Part 5: Design pressures, design stresses, scantling determination
— Part 6: Structural arrangements and details
©
ISO 2000 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 12215-1:2018

---------------------- Page: 10 ----------------------

SIST EN ISO 12215-1:2018
INTERNATIONAL STANDARD ISO 12215-1:2000(E)
Small craft — Hull construction and scantlings —
Part 1:
Materials: Thermosetting resins, glass-fibre reinforcement,
reference laminate
1 Scope
This part of ISO 12215 is applicable to thermosetting resins and glass-fibre reinforcement used in the construction of
small craft with a length of the hull (L ) of up to 24 m, in accordance with ISO 8666. This part of ISO 12215 specifies
H
the minimum requirements for material properties of glass reinforcement and resin matrix and the reference laminate
made thereof.
This part of ISO 12215 may be applicable to materials other than those specified, provided that the minimum require-
ments and properties of the reference laminate are met.
NOTE The underlying reason for preparing this International Standard is to harmonize existing standards and recommended
practices for loads on the hull and the dimensioning of sm
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.