SIST EN 528:2021
(Main)Rail dependent storage and retrieval equipment - Safety requirements for S/R machines
Rail dependent storage and retrieval equipment - Safety requirements for S/R machines
This document applies to all types of Storage and Retrieval (S/R) machines, restricted to the rails on which they travel within and outside the aisles for the storage and retrieval of unit loads and/or long goods such as bar materials and/or for order picking or similar duties. These machines shall embody lifting means along a mast and may include lateral handling facilities. Also included is the transfer equipment used to change between aisles. Control of machines may range from manual to fully automatic.
S/R-machine-related satellite vehicles according to definition 3.20 are included as a load-handling-device (LHD).
References in this standard to racking, buildings and systems only apply where it is necessary to assess the hazards and risks at their interfaces with S/R machines.
This document deals with all significant hazards relevant to rail dependent storage and retrieval equipment, when they are used under the conditions intended by the manufacturer including reasonably foreseeable misuse (see Annex F "List of significant hazards")).
This document applies to machines and equipment that are manufactured after the date of issue of this document.
Illustrations of examples of machines and transfer equipment to which this standard applies are shown in Annex A.
Safety requirements and/or measures in this standard apply to equipment used under indoor conditions. However, additional risk assessments and safety measures need to be considered for uses in severe conditions, e.g. extremely high temperatures, loads, the nature of which could lead to a dangerous situation (e.g. especially brittle loads, explosives), earthquake effects and also contact with foodstuff.
This document also deals with the technical requirements for electromagnetic compatibility (EMC).
Regalbediengeräte - Sicherheitsanforderungen
Dieses Dokument ist anzuwenden für alle Arten von Regalbediengeräten (RBG), die innerhalb und außerhalb der Regalgasse schienengebunden sind, die zum Ein- und Auslagern von Ladeeinheiten und/oder Langgut wie Stangenmaterial und/oder zur Kommissionierung oder zur Durchführung ähnlicher Funktionen dienen. Diese Maschinen müssen über eine Hubeinrichtung entlang eines Mastes verfügen und dürfen mit einem seitwärts agierenden Lastaufnahmemittel (LAM) ausgerüstet sein. Eingeschlossen sind Umsetzeinrichtungen für den Gassenwechsel. Die Steuerung der Geräte darf manuell bis vollautomatisch erfolgen.
Zu den Regalbediengeräten gehörende Satellitenfahrzeuge entsprechend Definition 3.15 sind als Lastaufnahmemittel inbegriffen.
Hinsichtlich Regalen, Gebäuden und Systemen findet diese Norm nur insoweit Anwendung, als eine Bewertung hinsichtlich Gefährdungen und Risiken im Zusammenhang mit Schnittstellen zu den Regalbediengeräten gegeben ist.
Dieses Dokument behandelt alle signifikanten Gefährdungen in Bezug auf Regalbediengeräte, wenn diese entsprechend den vom Hersteller vorgesehenen Bedingungen einschließlich vorhersehbarer Fehlanwendungen eingesetzt werden (siehe Anhang F, „Liste signifikanter und relevanter Gefährdungen“).
Dieses Dokument ist für Geräte und Einrichtungen anzuwenden, die nach dem Datum der Veröffentlichung dieses Dokuments auf den Markt gebracht wurden. Es wird eine Übergangsfrist von 12 Monaten vorgeschlagen.
Bildliche Darstellungen von Beispielen von Geräten und Umsetzeinrichtungen, für die diese Norm gilt, sind in Anhang A dargestellt.
Sicherheitsanforderungen und/oder -maßnahmen in dieser Norm gelten für Geräte, die in geschlossenen Räumen eingesetzt werden. Zusätzliche Risikobeurteilungen und Sicherheitsmaßnahmen sind bei Anwendungen unter erschwerten Bedingungen vorzunehmen, z. B. extrem hohen Temperaturen, Lasten, deren Eigenschaften zu gefährlichen Situationen führen könnten (z. B. besonders brüchige Lasten, Sprengstoff), Auswirkungen von Erdbeben und auch Kontakt mit Lebensmitteln.
Dieses Dokument beschäftigt sich auch mit den technischen Anforderungen zur elektromagnetischen Verträglichkeit (EMV).
Transtockeurs - Prescriptions de sécurité
Le présent document s'applique à tous les types d'appareils appelés transtockeurs destinés au stockage et au déstockage de charges unitaires et/ou de produits longs comme des barres, et/ou à la préparation de commandes ou tâches similaires, dont les déplacements dans et en dehors des allées sont guidés par les rails. Ces appareils comprennent des moyens de levage le long d'un mât et éventuellement des dispositifs de préhension latérale. Le présent document s'applique également au matériel permettant le transfert d'une allée à une autre. La commande des appareils peut aller du mode manuel au mode entièrement automatique.
Les chariots satellites associés à un transtockeur conformes à la définition 3.15 sont considérés comme un dispositif de manutention de charge.
Les références faites dans la présente norme aux rayonnages, aux bâtiments et aux systèmes ne s'appliquent que lorsqu'il est nécessaire d'évaluer les phénomènes dangereux et les risques encourus au niveau de leurs interfaces avec les transtockeurs.
Le présent document traite de tous les phénomènes dangereux significatifs relatifs aux transtockeurs, lorsque ceux-ci sont utilisés dans les conditions prévues par le fabricant, y compris les mauvais usages raisonnablement prévisibles (voir Annexe F « Liste des phénomènes dangereux significatifs »).
Le présent document s'applique aux appareils et équipements qui ont été fabriqués après sa date de parution. Une période de transition de 12 mois est proposée.
Des figures d'exemples de transtockeurs et de dispositifs de transfert auxquels s'applique la présente norme sont données à l'Annexe A.
Les prescriptions et/ou mesures de sécurité indiquées dans la présente norme s'appliquent aux appareils d'intérieur. Toutefois, il est nécessaire de considérer des appréciations de risques et des mesures de sécurité supplémentaires lors d'utilisations dans des conditions extrêmes comme, par exemple, les températures extrêmement élevées, les charges dont la nature est susceptible d'engendrer une situation dangereuse (par exemple, charges particulièrement fragiles, explosifs), les effets sismiques et également le contact avec la nourriture.
Le présent document traite également des prescriptions techniques relatives à la compatibilité électromagnétique (CEM).
Regalna dvigala in oprema - Varnostne zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 528:2021
01-junij-2021
Nadomešča:
SIST EN 528:2008
Regalna dvigala in oprema - Varnostne zahteve
Rail dependent storage and retrieval equipment - Safety requirements for S/R machines
Regalbediengeräte - Sicherheitsanforderungen
Transtockeurs - Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 528:2021
ICS:
53.080 Skladiščna oprema Storage equipment
SIST EN 528:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 528:2021
---------------------- Page: 2 ----------------------
SIST EN 528:2021
EN 528
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2021
EUROPÄISCHE NORM
ICS 53.080 Supersedes EN 528:2008
English Version
Rail dependent storage and retrieval equipment - Safety
requirements for S/R machines
Transtockeurs - Prescriptions de sécurité Regalbediengeräte - Sicherheitsanforderungen
This European Standard was approved by CEN on 4 January 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 528:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 528:2021
EN 528:2021 (E)
Contents Page
European foreword . 6
Introduction. 8
1 Scope . 9
2 Normative references . 9
3 Terms and definitions. 11
4 Safety requirements and/or protective/risk reduction measures . 14
4.1 General . 14
4.2 Control position . 14
4.2.1 General . 14
4.2.2 Access to and egress from the permanent on-board control position . 14
4.2.3 Floor of the on-board control position . 14
4.2.4 Design and dimensioning of permanent on-board control position . 14
4.2.5 Emergency call device on permanent on-board control positions . 15
4.2.6 Lighting on permanent on-board control position . 15
4.3 Control equipment . 16
4.3.1 General . 16
4.3.2 Safeguard of the operator on a permanent on-board control position . 16
4.3.3 Prevention of unauthorised operation (equipment switch) . 16
4.3.4 Changing mode of operation (mode switch) . 16
4.3.5 Key dependence . 17
4.3.6 Control devices for powered movements . 17
4.3.7 Control device identification . 17
4.3.8 Stop function . 17
4.3.9 Emergency stop function . 18
4.3.10 Safety requirements related to EMC . 18
4.4 Hoist unit . 18
4.4.1 Hoist unit brake . 18
4.4.2 Limitation of the lifting and lowering movement . 19
4.4.3 Overload and slack condition protection . 19
4.4.4 Safety gear and overspeed governor . 20
4.4.5 Suspension elements . 21
4.4.6 Hydraulic drives . 24
4.4.7 Lead-screw drive . 24
4.4.8 Rack and pinion drives . 25
4.5 Travel unit of the S/R machine . 25
4.5.1 Travel unit braking system . 25
4.5.2 Speed reducing system . 26
4.5.3 Limitation of travel . 26
4.5.4 Anti-derailment devices . 27
4.5.5 Stability . 27
4.6 Load handling devices . 28
4.6.1 Load stability. 28
4.6.2 Determination of possible impacts on the rack . 28
4.6.3 Rotating devices . 28
4.6.4 Interlocking functions . 28
4.6.5 Auxiliary handling equipment . 28
4.6.6 Load position monitoring . 29
2
---------------------- Page: 4 ----------------------
SIST EN 528:2021
EN 528:2021 (E)
4.6.7 Satellites . 29
4.7 Electrical equipment . 29
4.7.1 General . 29
4.7.2 Electrical supply conditions . 29
4.7.3 Environment . 29
4.7.4 Supply disconnecting (isolating) device . 29
4.7.5 Protection against electric shock . 30
4.7.6 Suspension of safeguarding . 30
4.7.7 Overriding of safety functions . 30
4.8 Transfer device . 30
4.8.1 General . 30
4.8.2 Retention of position . 31
4.8.3 Movement . 31
4.8.4 Interlocking functions . 31
4.8.5 Stability . 31
4.9 Maintenance repair and fault clearance . 31
4.9.1 General . 31
4.9.2 Maintenance position . 31
4.9.3 Emergency control position . 32
4.9.4 Speed limitation . 32
4.9.5 Communication . 33
4.9.6 Protection from operating machines (S/R machines and its transfer equipment) . 33
4.9.7 Access along the mast . 33
4.10 Machine environment . 35
4.10.1 General . 35
4.10.2 Communication of force information . 35
4.10.3 Safety clearances . 35
4.10.4 Safeguarding of persons (Limiting access) . 35
4.10.5 Load entry / exit points . 36
4.10.6 Escape from dangerous areas . 37
4.10.7 Protection against unintentional load movement. 38
4.10.8 Protection against falling . 39
5 Verification of safety requirements and/or measures . 39
5.1 Examination . 39
5.1.1 General . 39
5.1.2 Movements to be done . 39
5.1.3 Test of the safety gear . 39
5.1.4 Verification of the mechanical limits of travel . 40
5.1.5 Test of the lowering control valve . 40
5.1.6 Written record . 40
5.2 EMC . 40
5.3 Noise . 40
5.3.1 General . 40
5.3.2 Noise measurement . 40
5.3.3 Declaration . 41
5.4 Load tests . 42
5.4.1 Test load . 42
5.4.2 Static load test . 42
5.4.3 Dynamic load test . 42
5.4.4 Load test record . 42
6 Information for use . 42
6.1 General . 42
6.2 Erection on site. 42
6.3 Commissioning . 42
6.3.1 Method statement . 42
3
---------------------- Page: 5 ----------------------
SIST EN 528:2021
EN 528:2021 (E)
6.3.2 Instructions . 43
6.3.3 Training . 43
6.3.4 Safety devices . 43
6.3.5 Individual elements of the machine . 43
6.3.6 Integrated commissioning . 43
6.4 Normal operation . 43
6.4.1 General . 43
6.4.2 Operation and use . 43
6.4.3 Maintenance, repair and fault-clearing . 43
6.4.4 Spare parts . 43
6.4.5 Certification of suspension elements . 43
6.4.6 Noise declaration . 43
6.4.7 Test report . 44
6.4.8 Minimum markings . 44
6.4.9 Conditions for the safe operation of equipment . 44
6.5 Fault finding/troubleshooting . 47
6.5.1 General . 47
6.5.2 Description of safe access and egress to trouble points on the S/R machine . 47
6.5.3 Description of safe access and egress to trouble points at the interface between S/R
machine and racking . 47
6.5.4 Description of safe access and egress to trouble points at the interface between the
S/R machine and the conveying system . 47
6.5.5 Training . 47
6.6 Rescue of persons . 47
6.7 Maintenance, inspection, testing and training . 47
6.7.1 General . 47
6.7.2 Maintenance . 47
6.7.3 Periodic maintenance and testing . 48
6.7.4 Training . 49
6.8 Dismantling . 49
Annex A (informative) Figures. 50
Annex B (normative) Performance levels according to EN ISO 13849-1:2015 . 58
Annex C (normative) Preventing access to dangerous movements across the load entry/exit
points . 65
C.1 General . 65
C.2 Preventing access besides the conveyor . 65
C.2.1 Preventing access between conveyor and fixed guards . 65
C.2.2 Preventing access between conveyor tracks . 66
C.3 Preventing access under the conveyor . 67
C.4 Preventing access over the conveyor . 67
C.4.1 General . 67
C.4.2 Preventing access by limited opening height and tunnels . 67
C.4.3 Preventing access by minimum height of conveying level . 69
C.4.4 Preventing access by design of gravity roller conveyor . 71
C.4.5 Preventing access by mechanical guards . 73
C.5 Stopping the dangerous movement of the S/R-machines . 75
C.6 Additional organizational measures . 76
Annex D (normative) Access to restricted areas . 77
4
---------------------- Page: 6 ----------------------
SIST EN 528:2021
EN 528:2021 (E)
Annex E (normative) Verification of safety requirements and/or measures . 80
Annex F (normative) List of significant and relevant hazards . 87
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EU aimed to be covered . 92
Bibliography . 99
5
---------------------- Page: 7 ----------------------
SIST EN 528:2021
EN 528:2021 (E)
European foreword
This document (EN 528:2021) has been prepared by Technical Committee CEN/TC 149 “Power-operated
warehouse equipment”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2021, and conflicting national standards shall
be withdrawn at the latest by September 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
This document supersedes EN 528:2008.
The main changes compared to the previous edition EN 528:2008 are as follows:
— clearer / more understandable Annex C dealing with preventing access to dangerous movements
across the load entry/exit points;
— Annex ZA has been updated by introducing the generic template for Annex ZA amended in
accordance with decision of EU commission;
— revision and adaption of Annex B Performance level according to EN ISO 13849-1:2015;
— the scope has been stated more precisely;
— more readable and clearer text in standard due to avoidness of separate chapters for automatic and
manual machines;
— amendment or rather change of the following definitions (3):
— on-board control position (3.4), permanent on-board control position (3.5), load entry / exit
points (3.7), working place (3.8), pick and deposit station (3.9), restricted area (3.11), danger
area (3.12), satellite vehicle (3.15), powered access cabin (3.20), climb assistance system (3.21),
rated speed (3.22), normal operation (3.25), deleted definition 3.22 and renamed following
definitions;
— speed limitation (4.9.4) has been updated and been stated more precisely;
— where a powered access cabin is provided, it shall comply with the requirements for control positions
(4.9.7.2);
— Detachable ladders may be used up to a maximum height of 3 m (4.9.7);
— safety gear required for lifting carriages, that are designed to carry person(s) (4.4.4.1);
— the ratio of the minimum breaking force to the maximum static force for all types of suspension
elements to the lifting of persons has been reduced from 10 to 8 (4.4.5.1);
— requirements for additional person(s) on the lifting carriage has been stated more precisely (4.9.2.2);
6
---------------------- Page: 8 ----------------------
SIST EN 528:2021
EN 528:2021 (E)
— ladder along the mast shall be fitted with a guided type of a fall arresters according with EN 353-
1:2014+A1:2017 and anchor points at the transition points (4.9.3);
— prevention against load falling into adjacent automatically operated aisles: Safety level (PLr) is not
more dep
...
SLOVENSKI STANDARD
oSIST prEN 528:2019
01-oktober-2019
Regalna dvigala in oprema - Varnostne zahteve
Rail dependent storage and retrieval equipment - Safety requirements for S/R machines
Regalbediengeräte - Sicherheitsanforderungen
Transtockeurs - Prescriptions de sécurité
Ta slovenski standard je istoveten z: prEN 528
ICS:
53.080 Skladiščna oprema Storage equipment
oSIST prEN 528:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 528:2019
---------------------- Page: 2 ----------------------
oSIST prEN 528:2019
DRAFT
EUROPEAN STANDARD
prEN 528
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2019
ICS 53.080 Will supersede EN 528:2008
English Version
Rail dependent storage and retrieval equipment - Safety
requirements for S/R machines
Transtockeurs - Prescriptions de sécurité Regalbediengeräte - Sicherheitsanforderungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 149.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 528:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 528:2019
prEN 528:2019 (E)
Contents Page
European foreword . 6
Introduction . 8
1 Scope . 10
2 Normative references . 10
3 Terms and definitions . 12
4 Safety requirements and/or protective measures for all types of S/R machines . 15
4.1 General . 15
4.2 Control position . 15
4.2.1 Access to and egress from the permanent on-board control position . 15
4.2.2 General design and dimensioning of on-board control position . 15
4.2.3 Design and dimensioning of permanent on-board control position . 15
4.2.4 Warning equipment on permanent on-board control positions . 16
4.2.5 Lighting on permanent on-board control position . 17
4.3 Control equipment . 17
4.3.1 General . 17
4.3.2 Safeguard of the operator on a permanent on-board control position . 17
4.3.3 Prevention of unauthorised operation (equipment switch) . 17
4.3.4 Changing mode of operation (mode switch) . 18
4.3.5 Key dependence . 18
4.3.6 Control devices for powered movements. 18
4.3.7 Control device identification . 18
4.3.8 Stop function . 19
4.3.9 Emergency stop function . 19
4.3.10 Safety requirements related to EMC . 19
4.4 Hoist unit . 20
4.4.1 Hoist unit brake . 20
4.4.2 Limitation of the lifting and lowering movement . 20
4.4.3 Overload and slack condition protection . 21
4.4.4 Safety gear and overspeed governor. 21
4.4.5 Suspension elements . 22
4.4.6 Hydraulic drives . 25
4.4.7 Lead-screw drive . 26
4.4.8 Rack and pinion drives . 26
4.5 Travel unit of the S/R machine. 27
4.5.1 Travel unit braking system. 27
4.5.2 Speed reducing system . 28
4.5.3 Limitation of travel . 28
4.5.4 Anti-derailment devices . 28
4.5.5 Stability . 29
4.6 Load handling devices . 29
4.6.1 Load stability . 29
4.6.2 Limitation of forces . 29
4.6.3 Rotating devices. 30
4.6.4 Interlocks . 30
4.6.5 Auxiliary handling equipment . 30
4.6.6 Load position monitoring . 30
2
---------------------- Page: 4 ----------------------
oSIST prEN 528:2019
prEN 528:2019 (E)
4.6.7 Satellites . 30
4.7 Electrical equipment . 31
4.7.1 General . 31
4.7.2 Electrical supply conditions. 31
4.7.3 Environment . 31
4.7.4 Supply disconnecting (isolating) device . 31
4.7.5 Protection against electric shock . 32
4.7.6 Suspension of safeguarding . 32
4.7.7 Overriding of safety functions . 32
4.8 Transfer device . 32
4.8.1 General . 32
4.8.2 Retention of position . 32
4.8.3 Movement . 32
4.8.4 Interlocking . 33
4.8.5 Stability . 33
4.9 Maintenance repair and fault clearance . 33
4.9.1 General . 33
4.9.2 Maintenance position . 33
4.9.3 Emergency control position . 34
4.9.4 Speed limitation . 34
4.9.5 Communication . 35
4.9.6 Protection from operating machines (S/R machines and its transfer equipment) . 35
4.9.7 Access along the mast . 35
4.10 Machine environment . 36
4.10.1 General . 36
4.10.2 Communication of force information . 36
4.10.3 Safety clearances . 36
4.10.4 Safeguarding of persons (Limiting access) . 37
4.10.5 Load entry / exit points . 38
4.10.6 Interaction with other equipment . 39
4.10.7 Escape from dangerous areas . 39
4.10.8 Protection against unintentional load movement . 39
4.10.9 Protection of work stations and traffic areas . 40
4.10.10 . Protection against
falling . 40
5 Verification of safety requirements and/or measures . 41
5.1 Examination . 41
5.1.1 General . 41
5.1.2 Movements to be done . 41
5.1.3 Test of the safety gear . 41
5.1.4 Verification of the mechanical limits of travel . 41
5.1.5 Test of the lowering control valve . 41
5.2 Written record . 42
5.3 EMC . 42
5.4 Noise . 42
5.4.1 General . 42
5.4.2 Noise measurement . 42
5.4.3 Declaration . 43
5.5 Load tests . 43
5.5.1 Test load . 43
5.5.2 Static load test . 43
5.5.3 Dynamic load test . 43
3
---------------------- Page: 5 ----------------------
oSIST prEN 528:2019
prEN 528:2019 (E)
5.5.4 Load test record . 43
6 Information for use . 44
6.1 General . 44
6.2 Erection on site . 44
6.3 Commissioning . 44
6.3.1 Method statement . 44
6.3.2 Instructions . 44
6.3.3 Training . 44
6.3.4 Safety devices . 44
6.3.5 Individual elements of the machine . 44
6.3.6 Integrated commissioning . 44
6.4 Normal operation . 44
6.4.1 General . 44
6.4.2 Operation and use . 44
6.4.3 Maintenance, repair and fault-clearing . 45
6.4.4 Spare parts . 45
6.4.5 Certification of suspension elements . 45
6.4.6 Noise declaration . 45
6.4.7 Test report . 45
6.4.8 Minimum markings . 45
6.4.9 Conditions for the safe operation of equipment . 46
6.5 Fault finding/troubleshooting . 48
6.5.1 General . 48
6.5.2 Description of safe access and egress to trouble points on the S/R machine . 48
6.5.3 Description of safe access and egress to trouble points at the interface between S/R
machine and racking . 48
6.5.4 Description of safe access and egress to trouble points at the interface between the
S/R machine and the conveying system . 48
6.5.5 Training . 48
6.6 Rescue of persons. 49
6.7 Maintenance, inspection, testing and training . 49
6.7.1 General . 49
6.7.2 Maintenance . 49
6.7.3 Periodic maintenance and testing . 50
6.7.4 Training . 51
6.8 Dismantling . 51
Annex A (informative) Illustrations . 52
Annex B (normative) Performance levels according to EN ISO 13849-1:2015. 57
Annex C (normative) Preventing access to dangerous movements across the load entry/exit
points . 64
C.1 General . 64
C.2 Preventing access besides the conveyor. 64
C.2.1 Preventing access between conveyor and fixed guards . 64
C.2.2 Preventing access between gravity roller conveyor tracks . 66
C.3 Preventing access under the conveyor . 66
C.4 Preventing access over the conveyor . 66
C.4.1 Preventing access by limited opening height and tunnels . 67
4
---------------------- Page: 6 ----------------------
oSIST prEN 528:2019
prEN 528:2019 (E)
C.4.2 Preventing access by conveying height . 68
C.4.3 Preventing access by design of gravity roller conveyor . 70
C.4.4 Preventing access by mechanical guards . 71
C.5 Stopping the dangerous movement of the S/R-machines . 73
C.6 Additional organizational measures . 74
Annex D (normative) Access to restricted areas . 75
Annex E (normative) Verification of safety requirements and/or measures . 78
Annex F (informative) List of significant and relevant hazards . 86
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EU. 91
Bibliography . 98
5
---------------------- Page: 7 ----------------------
oSIST prEN 528:2019
prEN 528:2019 (E)
European foreword
This document (prEN 528:2019) has been prepared by Technical Committee CEN/TC 149 “Power-
operated warehouse equipment”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
This document supersedes EN 528:2008.
The main changes compared to the previous edition EN 528:2008 are as follows:
— clearer / more understandable Annex C dealing with preventing access to dangerous movements
across the load entry/exit points;
— Annex ZA has been updated by introducing the generic template for Annex ZA amended in
accordance with decision of EU commission;
— revision and adaption of Annex B Performance level according to EN ISO 13849-1:2015;
— the scope has been stated more precisely;
— more readable and clearer text in standard due to avoidness of separate chapters for automatic and
manual machine;
— amendment or rather change of the following definitions (3):
— on-board control position (3.4), permanent on-board control position (3.5), powered access
cabin (3.6), climb assistance system (3.7), rated speed (3.13), normal operation (3.19), satellite
vehicle (3.20), load entry / exit points (3.21), working place (3.22), pick and deposit (P&D)
station (3.24), restricted area (3.25), danger area (3.27);
— speed limitation (4.9.4) has been updated and been stated more precisely;
— an additional braking system is required if the end stops (e.g. buffers) are designed for a speed less
than 70 % of the rated speed (4.5.1.3);
— where a powered access cabin is provided, it shall comply with the requirements for control positions
(4.9.7.1);
— for detachable ladders on the lift mast a fall arrest system is required from a height of 3m onwards
(4.9.7);
— safety gear required for lifting carriages, that are designed to carry person(s) (4.4.4.1);
— the ratio of the minimum breaking force to the maximum static force for all types of suspension
elements to the lifting of persons has been reduced from 10 to 8 (4.4.5);
— requirements for additional person(s) on the lifting carriage has been stated more precisely (4.9.2.1);
6
---------------------- Page: 8 ----------------------
oSIST prEN 528:2019
prEN 528:2019 (E)
— ladder along the mast shall be fitted with a gu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.