SIST EN 300 220-2 V3.2.1:2018

ETSI EN 300 220-2 V3.2.1 (2018-06)






HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) operating
in the frequency range 25 MHz to 1 000 MHz;
Part 2: Harmonised Standard for access to radio spectrum
for non specific radio equipment

---------------------- Page: 1 ----------------------
2 ETSI EN 300 220-2 V3.2.1 (2018-06)



Reference
REN/ERM-TG28-535
Keywords
harmonised standard, radio, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2018.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 300 220-2 V3.2.1 (2018-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 All equipment conformance requirements . 10
4.2.0 Compliance . 10
4.2.1 Operating frequency . 10
4.2.1.0 Applicability. 10
4.2.1.1 Description . 11
4.2.1.2 Limits . 11
4.2.1.3 Conformance . 11
4.2.2 Unwanted emissions in the spurious domain . 11
4.2.2.0 Applicability. 11
4.2.2.1 Description . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.3 Transmitters conformance requirements . 11
4.3.1 Effective Radiated Power . 11
4.3.1.0 Applicability. 11
4.3.1.1 Description . 11
4.3.1.2 Limits . 11
4.3.1.3 Conformance . 11
4.3.2 Maximum e.r.p. power spectral density . 12
4.3.2.0 Applicability. 12
4.3.2.1 Description . 12
4.3.2.2 Limits . 12
4.3.2.3 Conformance . 12
4.3.3 Duty Cycle . 12
4.3.3.0 Applicability. 12
4.3.3.1 Description . 12
4.3.3.2 Limits . 12
4.3.3.3 Conformance . 12
4.3.4 Occupied Bandwidth. 12
4.3.4.0 Applicability. 12
4.3.4.1 Description . 12
4.3.4.2 Limits . 13
4.3.4.3 Conformance . 13
4.3.5 Tx Out of Band Emissions . 13
4.3.5.0 Applicability. 13
4.3.5.1 Description . 13
4.3.5.2 Limits . 13
4.3.5.3 Conformance . 13
4.3.6 Transient power . 13
4.3.6.0 Applicability. 13
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 300 220-2 V3.2.1 (2018-06)
4.3.6.1 Description . 13
4.3.6.2 Limits . 13
4.3.6.3 Conformance . 13
4.3.7 Adjacent Channel Power . 13
4.3.7.0 Applicability. 13
4.3.7.1 Description . 14
4.3.7.2 Limits . 14
4.3.7.3 Conformance . 14
4.3.8 TX behaviour under Low Voltage Conditions . 14
4.3.8.0 Applicability. 14
4.3.8.1 Description . 14
4.3.8.2 Limits . 14
4.3.8.3 Conformance . 14
4.3.9 Adaptive Power Control . 14
4.3.9.0 Applicability. 14
4.3.9.1 Description . 14
4.3.9.2 Limits . 14
4.3.9.3 Conformance . 14
4.3.10 FHSS equipment . 15
4.3.10.0 Applicability. 15
4.3.10.1 Description . 15
4.3.10.2 Limits . 15
4.3.10.3 Conformance . 15
4.3.11 Short term behaviour . 16
4.3.11.0 Applicability. 16
4.3.11.1 Description . 16
4.3.11.2 Limits . 16
4.3.11.3 Conformance . 16
4.4 Receivers conformance requirements . 16
4.4.1 RX sensitivity . 16
4.4.1.0 Applicability. 16
4.4.1.1 Description . 16
4.4.1.2 Limits . 16
4.4.1.3 Conformance . 16
4.4.2 Blocking . 16
4.4.2.0 Applicability. 16
4.4.2.1 Description . 16
4.4.2.2 Limits . 17
4.4.2.3 Conformance . 17
4.5 Polite spectrum access conformance requirement . 17
4.5.1 Description . 17
4.5.2 Clear Channel Assessment threshold . 17
4.5.2.0 Applicability. 17
4.5.2.1 Description . 17
4.5.2.2 Limits . 17
4.5.2.3 Conformance . 17
4.5.3 Polite spectrum access timing parameters . 17
4.5.3.1 Applicability. 17
4.5.3.2 Limits . 17
4.5.3.3 Conformance . 17
4.5.4 Adaptive Frequency Agility . 18
4.5.4.0 Applicability. 18
4.5.4.1 Description . 18
4.5.4.2 Limits . 18
4.5.4.3 Conformance . 18
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 19
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to
1 000 MHz . 21
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 300 220-2 V3.2.1 (2018-06)
Annex C (informative): National Radio Interfaces not EU wide harmonised . 23
Annex D (informative): Application form for testing . 28
D.1 Introduction . 28
D.2 Information to declare according to ETSI EN 300 220-2 . 28
Annex E (informative): Selection of technical parameters . 30
E.1 Introduction . 30
E.2 Receiver parameters . 30
Annex F (informative): Bibliography . 31
Annex G (informative): Change history . 32
History . 33

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 300 220-2 V3.2.1 (2018-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
For non EU countries the present document may be used for regulatory (Type Approval) purposes.

National transposition dates
Date of adoption of this EN: 15 June 2018
Date of latest announcement of this EN (doa): 30 September 2018
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2019
Date of withdrawal of any conflicting National Standard (dow): 31 March 2020

ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 300 220-2 V3.2.1 (2018-06)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part 2 of a multi-part deliverable covering Short Range Devices (SRD) operating in the
frequency range 25 MHz to 1 000 MHz.
The present document is structured as follows:
Clause 2 provides references.
Clause 3 provides definitions of terms and abbreviations used.
Clause 4 provides technical requirements.
Annex A (informative) provides a relationship between the present document and the essential requirements of
Directive 2014/53/EU [i.2].
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to 1 000 MHz.
Annex C (informative): National Radio Interfaces not EU wide harmonised.
Annex D (informative): Application form for testing.
Annex E (informative): Selection of parameters.
Annex F (informative): Bibliography.
Annex G (informative): Change history.
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 300 220-2 V3.2.1 (2018-06)
1 Scope
The present document specifies technical characteristics and methods of measurements for Non-specific Short Range
Devices category equipment types.
Non specific SRDs category is defined by the EU Commission Decision 2013/752/EU [i.3] as:
"The non-specific short-range device category covers all kinds of radio devices, regardless of the application or the
purpose, which fulfil the technical conditions as specified for a given frequency band. Typical uses include telemetry,
telecommand, alarms, data transmissions in general and other applications".
The present document covers equipment intended for fixed, portable, mobile or nomadic use, including:
• stand-alone radio equipment;
• plug-in radio devices intended for use with or within a variety of host systems;
• plug-in radio devices intended for use within combined equipment.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: SRDs frequency ranges
Short Range Devices frequency ranges
Transmit and receive 26,957 MHz to 27,283 MHz
Transmit and receive 40,660 MHz to 40,700 MHz
Transmit and receive 138,2 MHz to 138,45 MHz
Transmit and receive 169,4 MHz to 169,8125 MHz
Transmit and receive 433,040 MHz to 434,790 MHz
Transmit and receive 863 MHz to 876 MHz
Transmit and receive 915 MHz to 921 MHz
NOTE: It should be noted that not all frequency bands in table 1 are implemented in all European
countries. Annex B provides an overview of radio interfaces which are harmonised in the
European Union. Annex C provides an overview of national radio interfaces not harmonised in
the European Union.

It is noted that in the European Commission Decision on Short Range Devices [i.3], some harmonised frequency bands
may be subject to usage restrictions such as the exclusion of video or audio use.
Equipment transmitting voice with analog modulation are excluded from the present document.
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.2] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 8 ----------------------
9 ETSI EN 300 220-2 V3.2.1 (2018-06)
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 220-1 (V3.1.1) (02-2017): "Short Range Devices (SRD) operating in the frequency
range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".
[2] Commission Decision 2017/1483/EU Commission Implementing Decision (EU) 2017/1483 of
8 August 2017 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use
by short-range devices and repealing Decision 2006/804/EC on harmonisation of the radio
spectrum for use by short-range devic
...

Final draft ETSI EN 300 220-2 V3.2.1 (2018-04)






HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) operating
in the frequency range 25 MHz to 1 000 MHz;
Part 2: Harmonised Standard for access to radio spectrum
for non specific radio equipment

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 220-2 V3.2.1 (2018-04)



Reference
REN/ERM-TG28-535
Keywords
harmonised standard, radio, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2018.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 220-2 V3.2.1 (2018-04)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 All equipment conformance requirements . 10
4.2.0 Compliance . 10
4.2.1 Operating frequency . 10
4.2.1.0 Applicability. 10
4.2.1.1 Description . 11
4.2.1.2 Limits . 11
4.2.1.3 Conformance . 11
4.2.2 Unwanted emissions in the spurious domain . 11
4.2.2.0 Applicability. 11
4.2.2.1 Description . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.3 Transmitters conformance requirements . 11
4.3.1 Effective Radiated Power . 11
4.3.1.0 Applicability. 11
4.3.1.1 Description . 11
4.3.1.2 Limits . 11
4.3.1.3 Conformance . 11
4.3.2 Maximum e.r.p. power spectral density . 12
4.3.2.0 Applicability. 12
4.3.2.1 Description . 12
4.3.2.2 Limits . 12
4.3.2.3 Conformance . 12
4.3.3 Duty Cycle . 12
4.3.3.0 Applicability. 12
4.3.3.1 Description . 12
4.3.3.2 Limits . 12
4.3.3.3 Conformance . 12
4.3.4 Occupied Bandwidth. 12
4.3.4.0 Applicability. 12
4.3.4.1 Description . 12
4.3.4.2 Limits . 13
4.3.4.3 Conformance . 13
4.3.5 Tx Out of Band Emissions . 13
4.3.5.0 Applicability. 13
4.3.5.1 Description . 13
4.3.5.2 Limits . 13
4.3.5.3 Conformance . 13
4.3.6 Transient power . 13
4.3.6.0 Applicability. 13
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 220-2 V3.2.1 (2018-04)
4.3.6.1 Description . 13
4.3.6.2 Limits . 13
4.3.6.3 Conformance . 13
4.3.7 Adjacent Channel Power . 13
4.3.7.0 Applicability. 13
4.3.7.1 Description . 14
4.3.7.2 Limits . 14
4.3.7.3 Conformance . 14
4.3.8 TX behaviour under Low Voltage Conditions . 14
4.3.8.0 Applicability. 14
4.3.8.1 Description . 14
4.3.8.2 Limits . 14
4.3.8.3 Conformance . 14
4.3.9 Adaptive Power Control . 14
4.3.9.0 Applicability. 14
4.3.9.1 Description . 14
4.3.9.2 Limits . 14
4.3.9.3 Conformance . 14
4.3.10 FHSS equipment . 15
4.3.10.0 Applicability. 15
4.3.10.1 Description . 15
4.3.10.2 Limits . 15
4.3.10.3 Conformance . 15
4.3.11 Short term behaviour . 16
4.3.11.0 Applicability. 16
4.3.11.1 Description . 16
4.3.11.2 Limits . 16
4.3.11.3 Conformance . 16
4.4 Receivers conformance requirements . 16
4.4.1 RX sensitivity . 16
4.4.1.0 Applicability. 16
4.4.1.1 Description . 16
4.4.1.2 Limits . 16
4.4.1.3 Conformance . 16
4.4.2 Blocking . 16
4.4.2.0 Applicability. 16
4.4.2.1 Description . 16
4.4.2.2 Limits . 17
4.4.2.3 Conformance . 17
4.5 Polite spectrum access conformance requirement . 17
4.5.1 Description . 17
4.5.2 Clear Channel Assessment threshold . 17
4.5.2.0 Applicability. 17
4.5.2.1 Description . 17
4.5.2.2 Limits . 17
4.5.2.3 Conformance . 17
4.5.3 Polite spectrum access timing parameters . 17
4.5.3.1 Applicability. 17
4.5.3.2 Limits . 17
4.5.3.3 Conformance . 17
4.5.4 Adaptive Frequency Agility . 18
4.5.4.0 Applicability. 18
4.5.4.1 Description . 18
4.5.4.2 Limits . 18
4.5.4.3 Conformance . 18
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 19
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to
1 000 MHz . 21
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 220-2 V3.2.1 (2018-04)
Annex C (informative): National Radio Interfaces not EU wide harmonised . 23
Annex D (informative): Application form for testing . 28
D.1 Introduction . 28
D.2 Information to declare according to ETSI EN 300 220-2 . 28
Annex E (informative): Selection of technical parameters . 30
E.1 Introduction . 30
E.2 Receiver parameters . 30
Annex F (informative): Bibliography . 31
Annex G (informative): Change history . 32
History . 33

ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 300 220-2 V3.2.1 (2018-04)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
For non EU countries the present document may be used for regulatory (Type Approval) purposes.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

ETSI

---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 300 220-2 V3.2.1 (2018-04)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part 2 of a multi-part deliverable covering Short Range Devices (SRD) operating in the
frequency range 25 MHz to 1 000 MHz.
The present document is structured as follows:
Clause 2 provides references.
Clause 3 provides definitions of terms and abbreviations used.
Clause 4 provides technical requirements.
Annex A (informative) provides a relationship between the present document and essential requirements of
Directive 2014/53/EU [i.2].
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to 1 000 MHz.
Annex C (Informative): National Radio Interfaces not EU wide harmonised.
Annex D (informative): Application form for testing.
Annex E (informative): Selection of parameters.
Annex F (informative): Bibliography.
Annex G (informative): Change history.
ETSI

---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 300 220-2 V3.2.1 (2018-04)
1 Scope
The present document specifies technical characteristics and methods of measurements for Non-specific Short Range
Devices category equipment types.
Non specific SRDs category is defined by the EU Commission Decision 2013/752/EU [i.3] as:
"The non-specific short-range device category covers all kinds of radio devices, regardless of the application or the
purpose, which fulfil the technical conditions as specified for a given frequency band. Typical uses include telemetry,
telecommand, alarms, data transmissions in general and other applications".
The present document covers equipment intended for fixed, portable, mobile or nomadic use, including:
• stand-alone radio equipment;
• plug-in radio devices intended for use with or within a variety of host systems;
• plug-in radio devices intended for use within combined equipment.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: SRDs frequency ranges
Short Range Devices frequency ranges
Transmit and receive 26,957 MHz to 27,283 MHz
Transmit and receive 40,660 MHz to 40,700 MHz
Transmit and receive 138,2 MHz to 138,45 MHz
Transmit and receive 169,4 MHz to 169,8125 MHz
Transmit and receive 433,040 MHz to 434,790 MHz
Transmit and receive 863 MHz to 876 MHz
Transmit and receive 915 MHz to 921 MHz
NOTE: It should be noted that not all frequency bands in table 1 are implemented in all European
countries. Annex B provides an overview of radio interfaces which are harmonised in the
European Union. Annex C provides an overview of national radio interfaces not harmonised in
the European Union.

It is noted that in the European Commission Decision on Short Range Devices [i.3], some harmonised frequency bands
may be subject to usage restrictions such as the exclusion of video or audio use.
Equipment transmitting voice with analog modulation are excluded from the present document.
NOTE: The relationship between the present document and essential requirements of article 3.2 of
Directive 2014/53/EU [i.2] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 300 220-2 V3.2.1 (2018-04)
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 220-1 (V3.1.1) (02-2017): "Short Range Devices (SRD) operating in the frequency
range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".
[2] Commission Decision 2017/1483/EU Commission Implementing Decision (EU) 2017/1483 of
8 August 2017 amendin
...

Draft ETSI EN 300 220-2 V3.2.0 (2017-09)






HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) operating
in the frequency range 25 MHz to 1 000 MHz;
Part 2: Harmonised Standard for access to radio spectrum
for non specific radio equipment

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 220-2 V3.2.0 (2017-09)



Reference
REN/ERM-TG28-535
Keywords
harmonised standard, radio, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2017.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 220-2 V3.2.0 (2017-09)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 All equipment conformance requirements . 10
4.2.0 Compliance . 10
4.2.1 Operating frequency . 10
4.2.1.0 Applicability. 10
4.2.1.1 Description . 10
4.2.1.2 Limits . 10
4.2.1.3 Conformance . 10
4.2.2 Unwanted emissions in the spurious domain . 11
4.2.2.0 Applicability. 11
4.2.2.1 Description . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.3 Transmitters conformance requirements . 11
4.3.1 Effective Radiated Power . 11
4.3.1.0 Applicability. 11
4.3.1.1 Description . 11
4.3.1.2 Limits . 11
4.3.1.3 Conformance . 11
4.3.2 Maximum e.r.p. spectral density . 11
4.3.2.0 Applicability. 11
4.3.2.1 Description . 11
4.3.2.2 Limits . 12
4.3.2.3 Conformance . 12
4.3.3 Duty Cycle . 12
4.3.3.0 Applicability. 12
4.3.3.1 Description . 12
4.3.3.2 Limits . 12
4.3.3.3 Conformance . 12
4.3.4 Occupied Bandwidth. 12
4.3.4.0 Applicability. 12
4.3.4.1 Description . 12
4.3.4.2 Limits . 12
4.3.4.3 Conformance . 12
4.3.5 Tx Out of Band Emissions . 12
4.3.5.0 Applicability. 12
4.3.5.1 Description . 13
4.3.5.2 Limits . 13
4.3.5.3 Conformance . 13
4.3.6 Transient power . 13
4.3.6.0 Applicability. 13
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 220-2 V3.2.0 (2017-09)
4.3.6.1 Description . 13
4.3.6.2 Limits . 13
4.3.6.3 Conformance . 13
4.3.7 Adjacent Channel Power . 13
4.3.7.0 Applicability. 13
4.3.7.1 Description . 13
4.3.7.2 Limits . 13
4.3.7.3 Conformance . 13
4.3.8 TX behaviour under Low Voltage Conditions . 14
4.3.8.0 Applicability. 14
4.3.8.1 Description . 14
4.3.8.2 Limits . 14
4.3.8.3 Conformance . 14
4.3.9 Adaptive Power Control . 14
4.3.9.0 Applicability. 14
4.3.9.1 Description . 14
4.3.9.2 Limits . 14
4.3.9.3 Conformance . 14
4.3.10 FHSS equipment . 14
4.3.10.0 Applicability. 14
4.3.10.1 Description . 14
4.3.10.2 Limits . 14
4.3.10.3 Conformance . 15
4.3.11 Short term behaviour . 15
4.3.11.0 Applicability. 15
4.3.11.1 Description . 15
4.3.11.2 Limits . 15
4.3.11.3 Conformance . 15
4.4 Receivers conformance requirements . 16
4.4.1 RX sensitivity . 16
4.4.1.0 Applicability. 16
4.4.1.1 Description . 16
4.4.1.2 Limits . 16
4.4.1.3 Conformance . 16
4.4.2 Blocking . 16
4.4.2.0 Applicability. 16
4.4.2.1 Description . 16
4.4.2.2 Limits . 16
4.4.2.3 Conformance . 16
4.5 Polite spectrum access conformance requirement . 16
4.5.1 Description . 16
4.5.2 Clear Channel Assessment threshold . 17
4.5.2.0 Applicability. 17
4.5.2.1 Description . 17
4.5.2.2 Limits . 17
4.5.2.3 Conformance . 17
4.5.3 Polite spectrum access timing parameters . 17
4.5.3.1 Applicability. 17
4.5.3.2 Limits . 17
4.5.3.3 Conformance . 17
4.5.4 Adaptive Frequency Agility . 17
4.5.4.0 Applicability. 17
4.5.4.1 Description . 17
4.5.4.2 Limits . 17
4.5.4.3 Conformance . 17
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 18
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to
1 000 MHz . 20
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 220-2 V3.2.0 (2017-09)
Annex C (normative): National Radio Interfaces not EU wide harmonised . 23
Annex D (informative): Application form for testing . 28
D.1 Introduction . 28
D.2 Information to declare according to ETSI EN 300 220-2 . 28
Annex E (informative): Selection of technical parameters . 30
E.1 Introduction . 30
E.2 Receiver parameters . 30
Annex F (informative): Bibliography . 31
Annex G (informative): Change History . 32
History . 33

ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 220-2 V3.2.0 (2017-09)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
For non EU countries the present document may be used for regulatory (Type Approval) purposes.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 300 220-2 V3.2.0 (2017-09)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part 2 of a multi-part deliverable covering Short Range Devices (SRD) operating in the
frequency range 25 MHz to 1 000 MHz. Full details of the entire series can be found in part 1 [1].
The present document is structured as follows:
Clause 2 provides references.
Clause 3 provides definitions of terms and abbreviations used.
Clause 4 provides technical requirements.
Annex A (informative) provides a relationship between the present document and essential requirements of
Directive 2014/53/EU [i.2].
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to 1 000 MHz.
Annex C (normative): National Radio Interfaces not EU wide harmonised.
Annex D (informative): Application form for testing.
Annex E (informative): Selection of parameters.
Annex F (informative): Bibliography.
Annex G (informative): Change History.
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 300 220-2 V3.2.0 (2017-09)
1 Scope
The present document specifies technical characteristics and methods of measurements for Non-specific Short Range
Devices category equipment types.
Non specific SRDs category is defined by the EU Commission Decision 2013/752/EU [i.3] as:
"The non-specific short-range device category covers all kinds of radio devices, regardless of the application or the
purpose, which fulfil the technical conditions as specified for a given frequency band. Typical uses include telemetry,
telecommand, alarms, data transmissions in general and other applications".
The present document covers equipment intended for fixed, mobile or nomadic use, including:
• stand-alone radio equipment;
• plug-in radio devices intended for use with or within a variety of host systems;
• plug-in radio devices intended for use within combined equipment.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: SRDs frequency ranges
Short Range Devices frequency ranges
Transmit and receive 26,957 MHz to 27,283 MHz
Transmit and receive 40,660 MHz to 40,700 MHz
Transmit and receive 138,2 MHz to 138,45 MHz
Transmit and receive 169,4 MHz to 169,8125 MHz
Transmit and receive 433,040 MHz to 434,790 MHz
Transmit and receive 863 MHz to 876 MHz
Transmit and receive 915 MHz to 921 MHz
NOTE: It should be noted that not all frequency bands in table 1 are implemented in all European
countries. Annex B provides an overview of radio interfaces which are harmonised in the
European Union. Annex C provides an overview of national radio interfaces not harmonised in
the European Union.

It is noted that in the European Commission Decision on Short Range Devices [i.3], some harmonised frequency bands
may be subject to usage restrictions such as the exclusion of video or audio use.
Equipment transmitting voice with analog modulation are excluded from the present document.
NOTE: The relationship between the present document and essential requirements of article 3.2 of
Directive 2014/53/EU [i.2] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 8 ----------------------
9 Draft ETSI EN 300 220-2 V3.2.0 (2017-09)
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 220-1 (V3.1.1) (02-2017): "Short Range Devices (SRD) operating in the frequency
range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".
2.2 Informative references
References are either specific (identified by date of publication and/or e
...