Ships and marine technology — Major components of emergency towing arrangements

This document specifies the technical requirements, test methods, inspection rules and markings for major components of emergency towing arrangements (ETA) provided for tankers, gas carriers (LPG, LNG, etc.) and chemical vessels no less than 20 000 deadweight tonnes (DWT). It is only applicable to emergency towing arrangements as defined in 3.1. NOTE For any other applications, such as for mooring at a single point mooring (SPM) facility, the appropriate standards need to be referred to.

Navires et technologie maritime — Principaux éléments des dispositifs de remorquage d'urgence

General Information

Status
Published
Publication Date
31-Mar-2019
Current Stage
6060 - International Standard published
Due Date
11-Jan-2019
Completion Date
01-Apr-2019
Ref Project

Buy Standard

Standard
ISO 21130:2019 - Ships and marine technology -- Major components of emergency towing arrangements
English language
19 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 21130
First edition
2019-04
Ships and marine technology — Major
components of emergency towing
arrangements
Navires et technologie maritime — Principaux éléments des
dispositifs de remorquage d'urgence
Reference number
ISO 21130:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 21130:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 21130:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Technical requirements . 2
4.1 Major components of ETA . 2
4.2 Design arrangement of ETA . 2
4.3 Design and manufacturing requirements for major components . 3
4.3.1 Minimum strength requirement for ETA components . 3
4.3.2 Strength requirement for other parts . 3
4.3.3 Bow ETA . 3
4.3.4 Stern ETA . 5
5 Test method . 7
5.1 Bow ETA . 7
5.1.1 Prototype strength test for the bow ETA . 7
5.1.2 Fairlead . 7
5.1.3 Chain stopper . 7
5.1.4 Chafing chain . 8
5.1.5 Pedestal roller . 8
5.2 Stern ETA . . 8
5.2.1 Strength test for the stern ETA . 8
5.2.2 Fairlead . 8
5.2.3 Towing rope . 8
5.2.4 Stopper ring . 9
5.2.5 Strong point . 9
5.2.6 Storage container for the pick-up gear . 9
5.2.7 Storage winch . 9
5.3 Function test . 9
Annex A (informative) Type and dimensions of a fairlead .10
Annex B (informative) Chemical composition and mechanical properties of steel barsfor
ship anchor chains .11
Annex C (informative) Types and dimensions of chafing chains .12
Annex D (informative) Types and dimensions of chain stoppers .14
Annex E (informative) Type and dimensions of a towing rope .17
Annex F (informative) Types and dimensions of fairleads/strong points .18
Bibliography .19
© ISO 2019 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 21130:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 8, Ships and marine technology,
Subcommittee SC 4, Outfitting and deck machinery.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 21130:2019(E)
Ships and marine technology — Major components of
emergency towing arrangements
1 Scope
This document specifies the technical requirements, test methods, inspection rules and markings for
major components of emergency towing arrangements (ETA) provided for tankers, gas carriers (LPG,
LNG, etc.) and chemical vessels no less than 20 000 deadweight tonnes (DWT).
It is only applicable to emergency towing arrangements as defined in 3.1.
NOTE For any other applications, such as for mooring at a single point mooring (SPM) facility, the appropriate
standards need to be referred to.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3808, Road vehicles — Unscreened high-voltage ignition cables — General specifications, test methods
and requirements
ISO 4306-1, Cranes — Vocabulary — Part 1: General
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4306-1, ISO 3808 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
emergency towing arrangement
ETA
system equipped on tankers, gas carriers and chemical vessels, used to tow the vessel in an emergency
such as mechanical failure or lack of power
Note 1 to entry: The International Maritime Organization (IMO) requires that tankers, gas carriers and chemical
vessels of not less than 20 000 DWT and constructed since Jan 1, 1996, be provided with emergency towing
arrangements installed on both the bow and the stern.
3.2
safe working load
SWL
maximum permissible load determined after the equipment has been tested according to the relevant
regulations
© ISO 2019 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 21130:2019(E)

3.3
ultimate strength
certified minimum breaking load of a wire rope, chafing chain, shackle, etc.
Note 1 to entry: In the case of equipment such as chain stoppers, fairleads, etc., it can be defined as the load that
will cause a general failure of the structure or its attachment to the deck.
3.4
classification society
institution that establishes and maintains technical standards for the construction and operation of
ships and offshore facilities
4 Technical requirements
4.1 Major components of ETA
The major components of ETA are listed in Table 1 with their installation requirements.
Table 1 — ETA major components and installation requirements
Bow ETA Stern ETA Strength requirements
Component
(not preconfigured) (preconfigured) (see 4.3.1)
Pick-up gear Optional Required —
Towing rope Optional Required Required
Determined according to
Chafing chain Required Required
the design
Fairlead Required Required Required
Strong point Required Required Required
Determined according to
Pedestal rollers Required —
the design
4.2 Design arrangement of ETA
4.2.1 A typical arrangement of bow ETA is shown in Figure 1.
Key
1 pedestal rollers 3 fairlead 5 centreline of the chain
2 chain stopper 4 chafing chain 6 bulwark
NOTE The centreline of the chain is parallel to the deck.
Figure 1 — Typical arrangement of bow ETA
2 © ISO 2019 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 21130:2019(E)

4.2.2 A typical arrangement of stern ETA is shown in Figure 2.
Key
1 pick-up gear 3 fairlead 5 storage winch
2 towing rope 4 strong point 6 stern
Figure 2 — Typical arrangement of stern ETA
4.3 Design and manufacturing requirements for major components
4.3.1 Minimum strength requirement for ETA components
The minimum strength requirement for ETA components under stress during the towing operation is
given in Table 2.
Table 2 — Minimum strength requirement
Working strength Ultimate strength
Ship size
kN kN
20 000 tones ≤ DWT < 50 000 tonnes 1 000 2 000
50 000 tonnes ≤ DWT 2 000 4 000
The strength should be sufficient for all relevant angles of the towline, i.e. up to 90° from the ship's
centreline to the port and starboard and 30° vertical downwards.
4.3.2 Strength requirement for other parts
Other parts shall have sufficient strength to withstand the load to which they may be subjected in
towing operations.
4.3.3 Bow ETA
4.3.3.1 Fairlead
a) The fairlead shall be of a closed type, with the opening dimensions of at least 600 mm in width and
450 mm in height.
b) The fairlead should be capable of supporting the stress at the angles described in 4.3.1.
c) See Annex A for the general configuration of a bow fairlead.
d) Materials shall be weldable cast steel, e.g. 200-400 W in accordance with ISO 14737.
e) The fairlead shall be free from defects that affect its intended use, such as cracks, sand holes
and pores.
f) The SWL of the installed fairlead shall be marked at a conspicuous location on the fairlead.
© ISO 2019 – All rights reserved 3

---------------------- Page: 7 ----------------------
ISO 21130:2019(E)

4.3.3.2 Chafing chain
a) The chafing chain shall be of a welded stud type and made of materials of Grade III or better chain
steel. (See Annex B for the typical chemical composition and mechanical properties of steel bars for
a ship anchor chain). The minimum diameters of chafing chains are given in Table 3.
Table 3 — Minimum diameters of chafing chains
SWL Minimum diameter ϕ of chafing chains
kN mm
1 000 52
2 000 76
b) The length of chafing chain shall not be les
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.