Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 3: Pipes and fittings with non-smooth external surface, Type B

This document, together with ISO 21138‑1, specifies the definitions and requirements for pipes with a non-smooth external surface and a smooth internal surface (Type B), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications. NOTE 1 Pipes, fittings and the systems complying with this document can also be used for highway drainage and surface water. This document specifies test methods and test parameters. This document covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring stiffnesses, and gives recommendations concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes. In conjunction with ISO 21138‑1, this document is applicable to structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials. It is applicable to pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. NOTE 3 Pipes, fittings and other components conforming to any plastics product standards referred to in Clause 2 are deemed to be suitable for use with pipes and fittings conforming to this document, when they conform to the requirements for joint dimensions given in ISO 21138‑2 or ISO 21138‑3 (this document) and to the performance requirements given in Clause 10. NOTE 4 For dimensions larger than DN/OD 1200 or DN/ID 1200, this document can serve as general guidance regarding appearance, colour, physical and mechanical characteristics as well as performance requirements. Test methods are not included in this document.

Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement sans pression enterrés — Systèmes de canalisations à parois structurées en poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) — Partie 3: Tubes et raccords avec une surface externe non lisse, type B

General Information

Status
Published
Publication Date
19-Jan-2020
Current Stage
6060 - International Standard published
Start Date
20-Jan-2020
Due Date
13-Oct-2019
Completion Date
20-Jan-2020
Ref Project

Relations

Buy Standard

Standard
ISO 21138-3:2020 - Plastics piping systems for non-pressure underground drainage and sewerage -- Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)
English language
38 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 21138-3
Second edition
2020-01
Plastics piping systems for non-
pressure underground drainage and
sewerage — Structured-wall piping
systems of unplasticized poly(vinyl
chloride) (PVC-U), polypropylene (PP)
and polyethylene (PE) —
Part 3:
Pipes and fittings with non-smooth
external surface, Type B
Systèmes de canalisations en plastique pour les branchements et les
collecteurs d'assainissement sans pression enterrés — Systèmes de
canalisations à parois structurées en poly(chlorure de vinyle) non
plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) —
Partie 3: Tubes et raccords avec une surface externe non lisse, type B
Reference number
ISO 21138-3:2020(E)
©
ISO 2020

---------------------- Page: 1 ----------------------
ISO 21138-3:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 21138-3:2020(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions, symbols and abbreviated terms . 3
3.1 Terms and definitions . 3
3.2 Symbols . 4
3.3 Abbreviated terms . 4
4 Material . 5
4.1 General . 5
4.2 Unplasticized poly(vinyl chloride) (PVC-U) . 6
4.2.1 General. 6
4.2.2 Pipe and fitting material characteristics . 7
4.2.3 Utilization of non-virgin materials . 7
4.3 Polypropylene (PP) . 7
4.3.1 General. 7
4.3.2 Pipe and fitting material characteristics . 7
4.3.3 Melt mass-flow rate classification . 8
4.3.4 Utilization of non-virgin materials . 9
4.4 Polyethylene (PE) . 9
4.4.1 General. 9
4.4.2 Material characteristics of pipes and injection-moulded fittings . 9
4.4.3 Material characteristics of rotational-moulded fittings .10
4.4.4 Utilization of non-virgin materials .10
4.5 Sealing ring retaining components . .10
4.6 Sealing rings .10
4.7 Fused or welded joints .11
4.8 Adhesives for PVC-U .11
5 Designation of wall construction and examples of typical jointing methods .11
5.1 Wall constructions designated as Type B .11
5.1.1 Ribbed or corrugated construction .11
5.1.2 Typical jointing methods for structured-wall Type B pipes .11
5.2 Designation and design of joints.12
6 General characteristics for pipes and fittings — Colour .12
7 Geometrical characteristics .12
7.1 General .12
7.2 Dimensions .12
7.2.1 Designation .12
7.2.2 Lengths of pipe .12
7.2.3 Diameters of Type B pipes and spigots of pipes or fittings .12
7.2.4 Diameters and jointing dimensions of sockets and spigots.14
7.2.5 Wall thicknesses .15
7.3 Types of fitting.16
8 Physical characteristics .16
8.1 Unplasticized poly(vinyl chloride) (PVC-U) .16
8.1.1 Physical characteristics of PVC-U pipes .16
8.1.2 Physical characteristics of PVC-U fittings .17
8.2 Polypropylene (PP) .18
8.2.1 Physical characteristics of PP pipes .18
8.2.2 Physical characteristics of PP fittings .18
8.3 Polyethylene (PE) .19
© ISO 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 21138-3:2020(E)

8.3.1 Physical characteristics of PE pipes .19
8.3.2 Physical characteristics of PE fittings .19
9 Mechanical characteristics .19
9.1 Mechanical characteristics of pipes .19
9.1.1 General.19
9.1.2 Ring flexibility .21
9.1.3 Tensile strength of seams .21
9.1.4 Additional requirements .21
9.2 Mechanical characteristics of fittings .21
10 Performance requirements .22
11 Marking .24
11.1 General .24
11.2 Minimum required marking .24
11.2.1 Pipes .24
11.2.2 Fittings .24
Annex A (normative) Virgin PVC-U material .26
Annex B (normative) Utilization of non-virgin PVC-U material .27
Annex C (normative) Virgin PP material .30
Annex D (normative) Utilization of non-virgin PP material .31
Annex E (normative) Virgin PE material .33
Annex F (normative) Utilization of non-virgin PE material .34
Annex G (informative) Survey of possible use of reprocessed and recycled material .37
Bibliography .38
iv © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 21138-3:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for
the transport of fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including
land drainage).
This second edition cancels and replaces the first edition (ISO 21138-3:2007), which has been
technically revised. The main changes compared to the previous edition are as follows:
— the normative references have been updated;
— references to EN test methods have been updated to ISO test methods, when applicable;
— editorial improvements have been made for clarification.
A list of all parts in the ISO 21138 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
© ISO 2020 – All rights reserved v

---------------------- Page: 5 ----------------------
ISO 21138-3:2020(E)

Introduction
The ISO 21138 series of standards covers plastics piping systems for non-pressure underground
drainage and sewerage, in particular thermoplastics structured-wall piping systems.
vi © ISO 2020 – All rights reserved

---------------------- Page: 6 ----------------------
INTERNATIONAL STANDARD ISO 21138-3:2020(E)
Plastics piping systems for non-pressure underground
drainage and sewerage — Structured-wall piping
systems of unplasticized poly(vinyl chloride) (PVC-U),
polypropylene (PP) and polyethylene (PE) —
Part 3:
Pipes and fittings with non-smooth external surface, Type B
1 Scope
This document, together with ISO 21138-1, specifies the definitions and requirements for pipes with
a non-smooth external surface and a smooth internal surface (Type B), fittings and systems based on
unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall
piping systems intended to be used in non-pressure underground drainage and sewerage applications.
NOTE 1 Pipes, fittings and the systems complying with this document can also be used for highway drainage
and surface water.
This document specifies test methods and test parameters.
This document covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring
stiffnesses, and gives recommendations concerning colours.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these
aspects, taking into account their particular requirements and installation practices or codes.
In conjunction with ISO 21138-1, this document is applicable to structured-wall pipes and fittings, to
their joints and to joints with components of other plastics and non-plastics materials.
It is applicable to pipes and fittings with or without an integral socket with elastomeric ring seal joints
as well as welded and fused joints.
NOTE 3 Pipes, fittings and other components conforming to any plastics product standards referred to
in Clause 2 are deemed to be suitable for use with pipes and fittings conforming to this document, when they
conform to the requirements for joint dimensions given in ISO 21138-2 or ISO 21138-3 (this document) and to the
performance requirements given in Clause 10.
NOTE 4 For dimensions larger than DN/OD 1200 or DN/ID 1200, this document can serve as general guidance
regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.
Test methods are not included in this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 178, Plastics — Determination of flexural properties
ISO 306:2013, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 527-2:2012, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
© ISO 2020 – All rights reserved 1

---------------------- Page: 7 ----------------------
ISO 21138-3:2020(E)

ISO 580, Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for
visually assessing the effects of heating
ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics — Part 1: Standard method
ISO 1158, Plastics — Vinyl chloride homopolymers and copolymers — Determination of chlorine content
ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of
the resistance to internal pressure — Part 1: General method
ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of
the resistance to internal pressure — Part 2: Preparation of pipe test pieces
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pycnometer method and titration method
ISO 2507-1, Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method
ISO 2507-2, Thermoplastics pipes and fittings — Vicat softening temperature — Part 2: Test conditions for
unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and
for high impact resistance poly (vinyl chloride) (PVC-HI) pipes
ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
ISO 3127, Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method
ISO 3451-1, Plastics — Determination of ash — Part 1: General methods
ISO 4435:2003, Plastics piping systems for non-pressure underground drainage and sewerage —
Unplasticized poly(vinyl chloride) (PVC-U)
ISO 6259-1, Thermoplastics pipes — Determination of tensile properties — Part 1: General test method
ISO 6259-2, Thermoplastics pipes — Determination of tensile properties — Part 2: Pipes made of
unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly
(vinyl chloride) (PVC-HI)
ISO 8772:2006, Plastics piping systems for non-pressure underground drainage and sewerage —
Polyethylene (PE)
ISO 8773:2006, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene (PP)
ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified
temperature (DCMT) — Test method
ISO 9967, Thermoplastics pipes — Determination of creep ratio
ISO 9969, Thermoplastics pipes — Determination of ring stiffness
ISO 11173, Thermoplastics pipes — Determination of resistance to external blows — Staircase method
ISO 11357-6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation
induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
ISO 12091, Structured-wall thermoplastics pipes — Oven test
ISO 13229, Thermoplastics piping systems for non-pressure applications — Unplasticized poly(vinyl
chloride) (PVC-U) pipes and fittings — Determination of the viscosity number and K-value
ISO 13254, Thermoplastics piping systems for non-pressure applications — Test method for watertightness
2 © ISO 2020 – All rights reserved

---------------------- Page: 8 ----------------------
ISO 21138-3:2020(E)

ISO 13259, Thermoplastics piping systems for underground non-pressure applications — Test method for
leaktightness of elastomeric sealing ring type joints
ISO 13260, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Test
method for resistance to combined temperature cycling and external loading
ISO 13262, Thermoplastics piping systems for non-pressure underground drainage and sewerage —
Thermoplastics spirally-formed structured-wall pipes — Determination of the tensile strength of a seam
ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and sewerage —
Thermoplastics fittings — Test method for impact strength
ISO 13264, Thermoplastics piping systems for non-pressure underground drainage and sewerage —
Thermoplastics fittings — Test method for mechanical strength or flexibility of fabricated fittings
ISO 13265, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Joints
for buried non-pressure applications — Test method for the long-term sealing performance of joints with
elastomeric seals by estimating the sealing pressure
ISO 13967, Thermoplastics fittings — Determination of ring stiffness
ISO 13968, Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility
ISO 18373-1, Rigid PVC pipes — Differential scanning calorimetry (DSC) method — Part 1: Measurement of
the processing temperature
ISO 21138-1, Plastics piping systems for non-pressure underground drainage and sewerage — Structured-
wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene
(PE) — Part 1: Material specifications and performance criteria for pipes, fittings and the system
ISO 21138-2, Plastics piping systems for non-pressure underground drainage and sewerage — Structured-
wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene
(PE) — Part 2: Pipes and fittings with smooth external surface, Type B
ISO 22088-3, Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 3:
Bent strip method
EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 1: Vulcanized rubber
EN 681-2, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 2: Thermoplastic elastomers
EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 4: Cast polyurethane sealing elements
EN 10204:2004, Metallic products — Types of inspection documents
EN 12099, Plastics piping systems — Polyethylene piping materials and components — Determination of
volatile content
EN 15344, Plastics — Recycled plastics — Characterisation of polyethylene) (PE) recyclates
EN 15345, Plastics — Recycled plastics — Characterisation of polypropylene) (PP) recyclates
EN 15346:2014, Plastics — Recycled plastics — Characterisation of poly(vinyl chloride) (PVC) recyclates
3 Terms, definitions, symbols and abbreviated terms
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 21138-1 apply.
© ISO 2020 – All rights reserved 3

---------------------- Page: 9 ----------------------
ISO 21138-3:2020(E)

ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
3.2 Symbols
A length of engagement, or maximum pull-out whilst maintaining tightness
A minimum value of A
min
D inside diameter of a socket
i
D minimum value of D
i, min i
d outside diameter (of a pipe or a spigot)
e
d maximum value of the mean d
em, max e
d minimum value of the mean d
em, min e
d inside diameter of a pipe
i
d maximum value of the mean d
im, max i
d minimum value of the mean d
im, min i
e wall thickness (at any point)
e construction height
c
e wall thickness of the socket
2
e wall thickness of the groove
3
e wall thickness of the inside layer (waterway wall thickness)
4
e minimum value of e
4,min 4
e wall thickness of the inside layer under a hollow section
5
e minimum value of e
5,min 5
F distance from the end of a spigot to the effective sealing point
L length of a spigot
1
L minimum value of L
1,min 1
l effective length of a pipe
3.3 Abbreviated terms
CaCO calcium carbonate
3
CT close tolerance
DSC differential scanning calorimetry
4 © ISO 2020 – All rights reserved

---------------------- Page: 10 ----------------------
ISO 21138-3:2020(E)

MgCO magnesium carbonate
3
MFR melt mass-flow rate
OIT oxidation induction time
TIR true impact rate
TPE thermoplastic elastomer
VST Vicat softening temperature
4 Material
4.1 General
The material shall be one of the following: unplasticized poly (vinyl chloride) (PVC-U), polypropylene
(PP) or polyethylene (PE) to which are added those additives that are needed to facilitate the
manufacture of components conforming to this document, including the relevant annexes.
Spirally formed Type B pipes may include a support profile (see Figure 1) made from polymers other
than PVC-U, PP or PE.
Spirally formed pipe constructions may include a continuous elastomeric sealing component of
a material conforming to EN 681-1, EN 681-2 or EN 681-4 as applicable, or a continuous adhesive
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.