Ships and marine technology — Ship's mooring and towing fittings — Universal fairleads without upper roller

This International Standard specifies the design, size and technical requirements for universal fairleads without upper roller(s) installed to lead the mooring rope of a ship.

Navires et technologie maritime — Corps-morts et ferrures de remorquage de navires — Chaumards universels sans rouleau supérieur

General Information

Status
Withdrawn
Publication Date
24-Jun-2012
Withdrawal Date
24-Jun-2012
Current Stage
9599 - Withdrawal of International Standard
Completion Date
28-Aug-2020
Ref Project

Relations

Buy Standard

Standard
ISO 13742:2012 - Ships and marine technology -- Ship's mooring and towing fittings -- Universal fairleads without upper roller
English language
17 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 13742
First edition
2012-07-01
Ships and marine technology — Ship’s
mooring and towing fittings — Universal
fairleads without upper roller
Navires et technologie maritime — Corps-morts et ferrures de
remorquage de navires — Chaumards universels sans rouleau supérieur
Reference number
ISO 13742:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 13742:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 13742:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 1
4.1 Type . 1
4.2 Nominal sizes . 1
5 Dimensions . 2
6 Materials . 2
7 Construction . 2
8 Manufacturing and inspection . 2
9 Marking . 2
Annex A (informative) Basis for strength assessment of universal fairleads .14
Bibliography .17
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 13742:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13742 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee
SC 4, Outfitting and deck machinery.
iv © ISO 2012 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 13742:2012(E)
Introduction
The universal fairlead is a type of ship’s mooring fitting installed on board to lead the mooring rope from the
ship’s inboard to outboard.
A universal fairlead without upper roller is used for vessels in which the mooring deck level is higher than quay side.
© ISO 2012 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 13742:2012(E)
Ships and marine technology — Ship’s mooring and towing
fittings — Universal fairleads without upper roller
1 Scope
This International Standard specifies the design, size and technical requirements for universal fairleads without
upper roller(s) installed to lead the mooring rope of a ship.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
IMO Circular MSC/Circ.1175, Guidance on shipboard towing and mooring equipment
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
safe working load
SWL
maximum load in kN on the rope that should normally be applied in service conditions
4 Classification
4.1 Type
Depending on the construction, universal fairleads shall be classified as the following four types:
— type 3R: with one rope-passing opening;
— type 4RL: with one rope-passing opening with additional guide roller on left side;
— type 4RR: with one rope-passing opening with additional guide roller on right side;
— type 5R: with two rope-passing openings.
4.2 Nominal sizes
The nominal sizes, D , of universal fairleads are denoted by reference to the outside diameter of the main
n
roller in millimetres, in terms of the nearest number drawn from a basic series of preferred numbers. For the
universal fairleads having the same roller diameter, the alphabetical character is followed by the nominal size
for the different SWL.
The nominal sizes are:
140, 160, 180, 200, 250, 300A, 300B, 400A, 400B and 400C.
© ISO 2012 – All rights reserved 1

---------------------- Page: 6 ----------------------
ISO 13742:2012(E)
5 Dimensions
Universal fairleads have dimensions and particulars in accordance with Tables 1, 2, 3 and 4, and Figures 1,
2, 3, 4 and 5.
6 Materials
The materials of the following components are to be used for manufacturing the universal fairleads:
2
— Frame and other plates: weldable steel plates having a yield point of not less than 235 N/mm except frame
with rope guide for nominal size 400A, 400B and 400C shall be made of weldable steel plates having a
2
yield point of not less than 315 N/mm .
2
— Roller: weldable steel plates having a yield point of not less than 235 N/mm except rollers for nominal
size 400A, 400B and 400C shall be made of weldable steel plates having a yield point of not less than
2
315 N/mm , or equivalent steel tubes.
2
— Axle: carbon steel having a yield point of not less than 345 N/mm .
— Bush: brass or bronze or equivalent.
7 Construction
7.1 The rollers of the universal fairleads shall be constructed from steel tubes or formed from plate.
7.2 The foundation of the universal fairleads shall be determined by the manufacturer. The foundation and
welding connections to the hull shall be guaranteed reliable transmission of the maximum loading of the universal
fairleads to hull construction without any plastic deformation or cracks.
8 Manufacturing and inspection
8.1 All surfaces of the universal fairleads including welding shall be free from any visible flaws or imperfections.
8.2 All surfaces in contact with the ropes shall be free from surface roughness or irregularities likely to cause
damage to the ropes by abrasion.
8.3 The universal fairleads are to be coated externally with an anti-corrosion protective finish.
8.4 All rotating parts shall be provided with greasing.
9 Marking
9.1 The safe working load (SWL) intended for the use of the universal fairleads shall be noted in the towing and
mooring plan available on board for the guidance of the shipmaster as specified in MSC/Circ.1175.
9.2 The actual SWL on board shall be determined by considering the foundation and under deck reinforcement,
and it shall be marked on the towing and mooring plan. The actual SWL shall not be over the SWL indicated in
this International Standard.
9.3 The universal fairleads shall be clearly marked with its SWL by weld bead or equivalent. The SWL shall be
expressed in tonnes (letter ‘t’) and be placed so that it is not obscured during operation of the fitting.
EXAMPLE SWL XXX t
2 © ISO 2012 – All rights reserved

---------------------- Page: 7 ----------------------
ISO 13742:2012(E)
Dimensions in millimetres
© ISO 2012 – All rights reserved 3

---------------------- Page: 8 ----------------------
ISO 13742:2012(E)
Key
1 frame with rope guide
2 vertical rollers with housing and washers
3 lower horizontal roller with washers
4 vertical axles with stopper
5 lower horizontal axle with stoppers
a
Height of seat shall be determined in accordance with the hull construction design.
b
For nominal size 250 and above.
c
For nominal size 140 to 200 only.
d
Side shell.
e
For nominal size 300 and above.
Figure 1 — Assembly of type 3R universal fairleads
4 © ISO 2012 – All rights reserved

---------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.