ISO 18134-2:2024
(Main)Solid biofuels — Determination of moisture content — Part 2: Simplified method
Solid biofuels — Determination of moisture content — Part 2: Simplified method
This document specifies a method of determining the moisture content of a test sample of solid biofuels by drying in an oven and is used when the highest precision is not needed, e.g. for routine production control on site. The method described in this document is applicable to all solid biofuels. The moisture content of solid biofuels (as received) is always reported based on the total mass of the test sample (wet basis). NOTE Biomass materials can contain small amounts of volatile organic compounds (VOC) which can evaporate when determining moisture content by oven drying (see References [1] and [2]). The release of such compounds is quite small relative to the overall moisture content as determined by this method and is disregarded in this document.
Biocombustibles solides — Dosage de la teneur en humidité — Partie 2: Méthode simplifiée
Le présent document spécifie une méthode de détermination de la teneur en humidité d’un échantillon pour essai de biocombustibles solides par séchage à l’étuve. Cette méthode est utilisée lorsque la fidélité maximale n’est pas nécessaire, par exemple, pour un contrôle de routine de la production in situ. La méthode décrite dans le présent document est applicable à l’ensemble des biocombustibles solides. La teneur en humidité des biocombustibles solides (à réception) est toujours rapportée à la masse totale de l'échantillon pour essai (base humide). NOTE Les matériaux de la biomasse peuvent contenir de petites quantités de composés organiques volatils (COV) qui peuvent s'évaporer lors du dosage de la teneur en humidité par séchage à l’étuve (voir Références [1] et [2]). La libération de ces composés est très faible par rapport à la teneur en humidité globale telle que déterminée par cette méthode et n'est pas prise en compte dans le présent document.
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 18134-2
Third edition
Solid biofuels — Determination of
2024-03
moisture content —
Part 2:
Simplified method
Biocombustibles solides — Dosage de la teneur en humidité —
Partie 2: Méthode simplifiée
Reference number
ISO 18134-2:2024(en) © ISO 2024
---------------------- Page: 1 ----------------------
ISO 18134-2:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO 18134-2:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Sample preparation . 2
6.1 Sample reduction . .2
6.2 Pre-dried test sample .2
6.3 Mass of test portion . .2
7 Procedure . 2
7.1 Handling of test portion .2
7.2 Drying and weighing of test portion .3
8 Calculation . 3
8.1 General .3
8.2 Moisture content on a wet basis .3
8.3 Moisture content for pre-dried material .3
9 Performance characteristics .
...
Norme
internationale
ISO 18134-2
Troisième édition
Biocombustibles solides — Dosage
2024-03
de la teneur en humidité —
Partie 2:
Méthode simplifiée
Solid biofuels — Determination of moisture content —
Part 2: Simplified method
Numéro de référence
ISO 18134-2:2024(fr) © ISO 2024
---------------------- Page: 1 ----------------------
ISO 18134-2:2024(fr)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2024
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
© ISO 2024 – Tous droits réservés
ii
---------------------- Page: 2 ----------------------
ISO 18134-2:2024(fr)
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe. 1
5 Appareillage . 2
6 Préparation de l’échantillon . 2
6.1 Réduction de l'échantillon .2
6.2 Échantillon pour essai préséché .2
6.3 Masse de la prise d’essai.2
7 Mode opératoire . 3
7.1 Manipulation de la prise d’essai .3
7.2 Séchage et pesée de la prise d’essai .3
8 Calcul . 3
8.1 Généralités .3
8.2 Teneur en humidité sur base humide .3
8.3 Teneur en humidité pour un matériau préséché .4
9 Caractéristiques de performance .
...
FINAL DRAFT
International
Standard
ISO/FDIS 18134-2
ISO/TC 238
Solid biofuels — Determination of
Secretariat: SIS
moisture content —
Voting begins on:
2023-12-27
Part 2:
Simplified method
Voting terminates on:
2024-02-21
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 18134-2:2023(en) © ISO 2023
---------------------- Page: 1 ----------------------
FINAL DRAFT
ISO/FDIS 18134-2:2023(en)
International
Standard
ISO/FDIS 18134-2
ISO/TC 238
Solid biofuels — Determination of
Secretariat: SIS
moisture content —
Voting begins on:
Part 2:
Simplified method
Voting terminates on:
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
COPYRIGHT PROTECTED DOCUMENT
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2023
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 18134-2:2023(en) © ISO 2023
© ISO 2023 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO/FDIS 18134-2:2023(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Sample preparation . 2
6.1 Sample reduction . .2
6.2 Pre-dried test sample .2
6.3 Mass of test portion . .2
7 Procedure . 2
7.1 Handling of test portion .
...
2023-06-12
ISO/FDIS 18134-2:2023(E)
ISO /TC 238
Secretariat: SIS
Date: 2023-12-12
Solid biofuels — Determination of moisture content —
—
Part 2:
Simplified method
FDIS stage
---------------------- Page: 1 ----------------------
ISO/FDIS 18134-2:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: copyright@iso.org
Website: www.iso.orgwww.iso.org
Published in Switzerland
ii © ISO 2023 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO/FDIS 18134-2:2023(E)
Contents
Foreword . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Sample preparation . 2
6.1 Sample reduction . 2
6.2 Pre-dried test sample . 2
6.3 Mass of test portion . 2
7 Procedure . 2
7.1 Handling of test portion . 2
7.2 Weighing of test portion . 3
8 Calculation . 3
8.1 General . 3
8.2 Moisture content on a wet basis . 3
8.3 Moisture content for pre-dried material . 3
9 Performance characteristics . 4
10 Test report . 4
Bibliography . 5
Foreword iv
1 Scope 1
2 Normative references 1
3 Terms and definitions 1
4 Principle 1
5 Apparatus 1
6 Sample preparation 2
6.1 Sample reduction 2
6.2 Pre-dried test sample 2
6.3 Mass of test portion 2
7 Procedure 2
7.1 Handling
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.