Rolling bearings — Balls — Part 1: Steel balls

ISO 3290-1:2014 specifies requirements for finished steel balls for rolling bearings.

Roulements — Billes — Partie 1: Billes de roulement en acier

ISO 3290-1:2014 fixe les exigences des billes finies, en acier, utilisées pour les roulements.

Kotalni ležaji - Kroglice - 1. del: Jeklene kroglice

Ta del standarda ISO 3290 določa zahteve za dokončane jeklene kroglice za kotalne ležaje.

General Information

Status
Published
Publication Date
21-Aug-2014
Current Stage
9093 - International Standard confirmed
Completion Date
07-Jan-2020

Relations

Buy Standard

Standard
ISO 3290-1:2014 - Rolling bearings -- Balls
English language
14 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 3290-1:2015
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 3290-1:2014 - Roulements -- Billes
French language
14 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3290-1
Second edition
2014-09-01
Rolling bearings — Balls —
Part 1:
Steel balls
Roulements — Billes —
Partie 1: Billes de roulement en acier
Reference number
ISO 3290-1:2014(E)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO 3290-1:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3290-1:2014(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 4
5 Requirements . 4
5.1 Ball size . 4
5.2 Quality of geometry and surface . 4
5.3 Sorting accuracy and ball gauges . 5
5.4 Hardness . 5
6 Dimensions and tolerances . 5
6.1 General . 5
6.2 Shortened formats for nominal diameter identification . 5
Annex A (normative) Method for assessment of deviation from spherical form .11
Annex B (normative) Illustration of ball gauges and sorting principles.12
Bibliography .14
© ISO 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3290-1:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword – Supplementary information.
The committee responsible for this document is ISO/TC 4, Rolling bearings, Subcommittee SC 12, Ball
bearings.
This second edition cancels and replaces the first edition (ISO 3290-1:2008), which has been technically
revised. It also incorporates Technical Corrigendum ISO 3290-1:2008/Cor.1:2009. In particular,
“material”, specified in Clause 6 of the first edition, has been deleted.
ISO 3290 consists of the following parts, under the general title Rolling bearings — Balls:
— Part 1: Steel balls
— Part 2: Ceramic balls
iv © ISO 2014 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3290-1:2014(E)
Rolling bearings — Balls —
Part 1:
Steel balls
1 Scope
This part of ISO 3290 specifies requirements for finished steel balls for rolling bearings.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 1132-1, Rolling bearings — Tolerances — Part 1: Terms and definitions
ISO 4288, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Rules and
procedures for the assessment of surface texture
ISO 5593, Rolling bearings — Vocabulary
ISO 12181-1, Geometrical product specifications (GPS) — Roundness — Part 1: Vocabulary and parameters
of roundness
ISO 15241, Rolling bearings — Symbols for physical quantities
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1132-1, ISO 5593, and the
following apply.
3.1
ball gauge
amount by which the mean diameter of ball lot should differ from the nominal ball diameter, this amount
being one of an established series
Note 1 to entry: Each ball gauge is a whole multiple of the ball gauge interval established for the ball grade in
question.
Note 2 to entry: A ball gauge, in combination with the ball grade and nominal diameter, is considered as the most
exact ball size specification to be used by a customer for ordering purposes.
[SOURCE: ISO 5593:1997, 05.04.09, modified — Notes 1 and 2 to entry have been added.]
3.2
ball gauge interval
absolute difference of two consecutive ball gauges
3.3
ball grade
specific combination of dimensional, form, surface roughness and sorting tolerances for balls
Note 1 to entry: Ball grade is identified by the letter G and a number, e.g. G 20.
© ISO 2014 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 3290-1:2014(E)

[SOURCE: ISO 5593:1997, 05.04.08, modified — Note 1 to entry has been added.]
3.4
ball lot
definite quantity of balls manufactured under conditions presumed uniform and which is considered as
an entity
[SOURCE: ISO 5593:1997, 05.04.05]
3.5
ball subgauge
amount, of an established series of amounts, which is the nearest to the actual deviation from the ball
gauge of a ball lot
Note 1 to entry: Each ball subgauge is a whole multiple of the ball subgauge interval established for the ball grade
in question.
Note 2 to entry: The ball subgauge, in combination with the nominal ball diameter and the ball gauge, is used by
ball manufacturers to denote the mean diameter of a ball lot and is not generally used by customers for ordering
purposes.
[SOURCE: ISO 5593:1997, 05.04.11, modified — Notes 1 and 2 to entry have been added.]
3.6
ball subgauge interval
absolute difference of two consecutive ball subgauges
3.7
deviation from spherical ball surface
various types of deviation from the perfect spherical ball surface, uniformly or non-uniformly distributed
and repeated around the ball surface
Note 1 to entry: The deviations to which limits can be attributed are
— deviation from spherical form,
— surface defect,
— surface roughness, and
— waviness.
3.7.1
deviation from spherical form
radial distance between the smallest circumscribed sphere and the greatest inscribed sphere, with
their centres common to the least squares sphere centre
Note 1 to entry: This definition supersedes ISO 5593:1997, 05.06.03.
3.7.2
surface defect
element, irregularity, or group of elements and irregularities of the real surface, unintentionally or
accidentally caused during manufacture, storage, handling or use of the surface
Note 1 to entry: These types of element or irregularity differ considerably from those constituting the surface
roughness and are not considered during the measurement of the surface roughness.
Note 2 to entry: The limits for surface defects are not specified in this part of ISO 3290.
2 © ISO 2014 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 3290-1:2014(E)

3.7.3
surface roughness
surface irregularities with relatively small spacings, which usually include irregularities resulting from
the method of manufacture being used and/or other influences
Note 1 to entry: These irregularities are considered within the limits that are conventionally defined, e.g. within
the limits of the sampling length.
3.7.4
waviness
surface irregularities of random or periodical deviation from the ideal spherical form
Note 1 to entry: Waviness shall be evaluated by default as velocity amplitude.
Note 2 to entry: In practice, the waviness components are separated from the real surface by a waviness analyser
(filters).
3.8
deviation of a ball lot from ball gauge
difference between the mean diameter of a ball lot and the sum of the nominal ball diameter and the ball
gauge
[SOURCE: ISO 5593:1997, 05.04.10]
3.9
hardness
measure of resistance to penetration as determined by a specific test method
Note 1 to entry: For steel balls, such a test method is generally the Rockwell hardness test.
3.10
mean ball diameter
arit
...

SLOVENSKI STANDARD
SIST ISO 3290-1:2015
01-april-2015
1DGRPHãþD
SIST ISO 3290-1:2009
SIST ISO 3290-1:2009/Cor 1:2009
Kotalni ležaji - Kroglice - 1. del: Jeklene kroglice
Rolling bearings - Balls - Part 1: Steel balls
Roulements - Billes - Partie 1: Billes de roulement en acier
Ta slovenski standard je istoveten z: ISO 3290-1:2014
ICS:
21.100.20 Kotalni ležaji Rolling bearings
SIST ISO 3290-1:2015 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 3290-1:2015

---------------------- Page: 2 ----------------------

SIST ISO 3290-1:2015
INTERNATIONAL ISO
STANDARD 3290-1
Second edition
2014-09-01
Rolling bearings — Balls —
Part 1:
Steel balls
Roulements — Billes —
Partie 1: Billes de roulement en acier
Reference number
ISO 3290-1:2014(E)
©
ISO 2014

---------------------- Page: 3 ----------------------

SIST ISO 3290-1:2015
ISO 3290-1:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 3290-1:2015
ISO 3290-1:2014(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 4
5 Requirements . 4
5.1 Ball size . 4
5.2 Quality of geometry and surface . 4
5.3 Sorting accuracy and ball gauges . 5
5.4 Hardness . 5
6 Dimensions and tolerances . 5
6.1 General . 5
6.2 Shortened formats for nominal diameter identification . 5
Annex A (normative) Method for assessment of deviation from spherical form .11
Annex B (normative) Illustration of ball gauges and sorting principles.12
Bibliography .14
© ISO 2014 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 3290-1:2015
ISO 3290-1:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword – Supplementary information.
The committee responsible for this document is ISO/TC 4, Rolling bearings, Subcommittee SC 12, Ball
bearings.
This second edition cancels and replaces the first edition (ISO 3290-1:2008), which has been technically
revised. It also incorporates Technical Corrigendum ISO 3290-1:2008/Cor.1:2009. In particular,
“material”, specified in Clause 6 of the first edition, has been deleted.
ISO 3290 consists of the following parts, under the general title Rolling bearings — Balls:
— Part 1: Steel balls
— Part 2: Ceramic balls
iv © ISO 2014 – All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 3290-1:2015
INTERNATIONAL STANDARD ISO 3290-1:2014(E)
Rolling bearings — Balls —
Part 1:
Steel balls
1 Scope
This part of ISO 3290 specifies requirements for finished steel balls for rolling bearings.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 1132-1, Rolling bearings — Tolerances — Part 1: Terms and definitions
ISO 4288, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Rules and
procedures for the assessment of surface texture
ISO 5593, Rolling bearings — Vocabulary
ISO 12181-1, Geometrical product specifications (GPS) — Roundness — Part 1: Vocabulary and parameters
of roundness
ISO 15241, Rolling bearings — Symbols for physical quantities
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1132-1, ISO 5593, and the
following apply.
3.1
ball gauge
amount by which the mean diameter of ball lot should differ from the nominal ball diameter, this amount
being one of an established series
Note 1 to entry: Each ball gauge is a whole multiple of the ball gauge interval established for the ball grade in
question.
Note 2 to entry: A ball gauge, in combination with the ball grade and nominal diameter, is considered as the most
exact ball size specification to be used by a customer for ordering purposes.
[SOURCE: ISO 5593:1997, 05.04.09, modified — Notes 1 and 2 to entry have been added.]
3.2
ball gauge interval
absolute difference of two consecutive ball gauges
3.3
ball grade
specific combination of dimensional, form, surface roughness and sorting tolerances for balls
Note 1 to entry: Ball grade is identified by the letter G and a number, e.g. G 20.
© ISO 2014 – All rights reserved 1

---------------------- Page: 7 ----------------------

SIST ISO 3290-1:2015
ISO 3290-1:2014(E)

[SOURCE: ISO 5593:1997, 05.04.08, modified — Note 1 to entry has been added.]
3.4
ball lot
definite quantity of balls manufactured under conditions presumed uniform and which is considered as
an entity
[SOURCE: ISO 5593:1997, 05.04.05]
3.5
ball subgauge
amount, of an established series of amounts, which is the nearest to the actual deviation from the ball
gauge of a ball lot
Note 1 to entry: Each ball subgauge is a whole multiple of the ball subgauge interval established for the ball grade
in question.
Note 2 to entry: The ball subgauge, in combination with the nominal ball diameter and the ball gauge, is used by
ball manufacturers to denote the mean diameter of a ball lot and is not generally used by customers for ordering
purposes.
[SOURCE: ISO 5593:1997, 05.04.11, modified — Notes 1 and 2 to entry have been added.]
3.6
ball subgauge interval
absolute difference of two consecutive ball subgauges
3.7
deviation from spherical ball surface
various types of deviation from the perfect spherical ball surface, uniformly or non-uniformly distributed
and repeated around the ball surface
Note 1 to entry: The deviations to which limits can be attributed are
— deviation from spherical form,
— surface defect,
— surface roughness, and
— waviness.
3.7.1
deviation from spherical form
radial distance between the smallest circumscribed sphere and the greatest inscribed sphere, with
their centres common to the least squares sphere centre
Note 1 to entry: This definition supersedes ISO 5593:1997, 05.06.03.
3.7.2
surface defect
element, irregularity, or group of elements and irregularities of the real surface, unintentionally or
accidentally caused during manufacture, storage, handling or use of the surface
Note 1 to entry: These types of element or irregularity differ considerably from those constituting the surface
roughness and are not considered during the measurement of the surface roughness.
Note 2 to entry: The limits for surface defects are not specified in this part of ISO 3290.
2 © ISO 2014 – All rights reserved

---------------------- Page: 8 ----------------------

SIST ISO 3290-1:2015
ISO 3290-1:2014(E)

3.7.3
surface roughness
surface irregularities with relatively small spacings, which usually include irregularities resulting from
the method of manufacture being used and/or other influences
Note 1 to entry: These irregularities are considered within the limits that are conventionally defined, e.g. within
the limits of the sampling length.
3.7.4
waviness
surface irregularities of random or periodical deviation from the ideal spherical form
Note 1 to entry: Waviness shall be evaluated by default as velocity amplitude.
Note 2 to entry: In practice, the waviness components are separated from the real surface by a waviness analyser
(filters).
3.8
deviation of a ball lot from ball gauge
difference between the
...

NORME ISO
INTERNATIONALE 3290-1
Deuxième édition
2014-09-01
Roulements — Billes —
Partie 1:
Billes de roulement en acier
Rolling bearings — Balls —
Part 1: Steel balls
Numéro de référence
ISO 3290-1:2014(F)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO 3290-1:2014(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2014
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2014 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 3290-1:2014(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Symboles . 4
5 Exigences . 4
5.1 Dimension des billes . 4
5.2 Qualités géométriques et de surface . 4
5.3 Exactitude du classement et classes de billes . 5
5.4 Dureté . 5
6 Dimensions et tolérances . 5
6.1 Généralités . 5
6.2 Formats abrégés pour identification du diamètre nominal . 5
Annex A (normative) Méthode d’évaluation de l’écart de sphéricité .11
Annex B (normative) Illustration des classes de bille et des principes de classement .12
Bibliographie .14
© ISO 2014 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 3290-1:2014(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui concerne
la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les
références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l’élaboration
du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de brevets reçues par
l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à l’évaluation de
la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes de l’OMC concernant
les obstacles techniques au commerce (OTC), voir le lien suivant: Avant-propos — Informations
supplémentaires.
Le comité chargé de l’élaboration du présent document est l’ISO/TC 4, Roulements, sous-comité SC 12,
Roulements à billes.
Cette deuxième édition annule et remplace la première édition (ISO 3290-1:2008), qui a fait l’objet d’une
révision technique. Elle intègre également le Rectificatif Technique ISO 3290-1:2008/Cor.1:2009. En
particulier, les «Matériaux», spécifiés à l’Article 6 de la première édition, ont été supprimés.
L’ISO 3290 comprend les parties suivantes, présentées sous le titre général Roulements — Billes:
— Partie 1: Billes de roulement en acier
— Partie 2: Billes de roulement en céramique
iv © ISO 2014 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 3290-1:2014(F)
Roulements — Billes —
Partie 1:
Billes de roulement en acier
1 Domaine d’application
La présente partie de l’ISO 3290 fixe les exigences des billes finies, en acier, utilisées pour les roulements.
2 Références normatives
Les documents suivants, en tout ou partie, sont référencés de manière normative dans le présent
document et sont indispensables à son application. Pour les références datées, seule l’édition citée
s’applique. Pour les références non datées, la dernière édition du document de référence s’applique (y
compris les éventuels amendements).
ISO 1132-1, Roulements — Tolérances — Partie 1: Termes et définitions
ISO 4288, Spécification géométrique des produits (GPS) — État de surface: Méthode du profil — Règles et
procédures pour l’évaluation de l’état de surface
ISO 5593, Roulements — Vocabulaire
ISO 12181-1, Spécification géométrique des produits (GPS) — Circularité — Partie 1: Vocabulaire et
paramètres de circularité
ISO 15241, Roulements — Symboles relatifs aux grandeurs physiques
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l’ISO 1132-1, ISO 5593 ainsi
que les suivants s’appliquent.
3.1
classe de bille
choisie dans une série préétablie, valeur dont il convient que le diamètre moyen d’un lot de billes s’écarte
du diamètre nominal de bille
Note 1 à l’article: Chaque classe de bille s’exprime par un multiple entier de l’intervalle de classement correspondant
au grade considéré.
Note 2 à l’article: Il convient de considérer que la classe, associée au grade et au diamètre nominal, constitue
l’indication la plus exacte de dimension, qui puisse être utilisée pour la rédaction des commandes.
[SOURCE: ISO 5593:1997, 05.04.09, modifiée — Notes 1 et 2 à l’article ont été ajoutées]
3.2
intervalle de classement
différence absolue entre deux classes de bille consécutives
3.3
grade de bille
ensemble de tolérances associées aux dimensions, à la forme, à la rugosité et au classement des billes
Note 1 à l’article: Le grade de bille est désigné par la lettre G et un nombre, par exemple G 20.
© ISO 2014 – Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 3290-1:2014(F)

[SOURCE: ISO 5593:1997, 05.04.08 modifiée — Note 1 à l’article a été ajoutée]
3.4
lot de billes
quantité donnée de billes fabriquées dans des conditions réputées uniformes, considérée comme un
ensemble
[SOURCE: ISO 5593:1997, 05.04.05]
3.5
sous-classe de bille
nombre choisi dans une série préétablie, le plus proche de l’écart réel du lot de bille par rapport à la
classe
Note 1 à l’article: Chaque sous-classe de bille s’exprime par un multiple entier de l’intervalle de sous-classement,
pour le grade de bille considéré.
Note 2 à l’article: Associée au diamètre nominal de bille et à la classe de bille, la sous-classe est utilisée, par les
fabricants, comme repère de position du diamètre moyen du lot de billes; généralement, elle n’est pas utilisée par
les clients lors des commandes.
[SOURCE: ISO 5593:1997, 05.04.11 modifiée — Notes 1 et 2 à l’article ont été ajoutées]
3.6
intervalle de sous-classement
différence absolue entre deux sous-classes de bille consécutives
3.7
écart par rapport à la surface d’une bille sphérique
tout type d’écart par rapport à la surface sphérique parfaite d’une bille, distribué et répété non
uniformément ou uniformément autour de la surface d’une bille
Note 1 à l’article: Les écarts auxquels des limites peuvent être allouées sont:
— écarts de sphéricité,
— défaut de surface,
— rugosité de surface, et
— ondulation.
3.7.1
écart de sphéricité
distance radiale entre la plus petite sphère circonscrite et la plus grande sphère inscrite ayant leur
centre commun au centre de la sphère des moindres carrés
Note 1 à l’article: Cette définition remplace ISO 5593:1997, 05.06.03.
3.7.2
défaut de surface
élément, irrégularité ou groupe d’éléments et d’irrégularités de la surface réelle, provoqués non
intentionnellement ou accidentellement pendant la fabrication, le stockage, la manutention ou l’utilisation
de la surface
Note 1 à l’article: Ces types d’éléments ou d’irrégularités diffèrent considérablement de ceux constitutifs de la
rugosité de surface et ne sont pas pris en compte au cours du mesurage de la rugosité de surface.
Note 2 à l’article: Les limites des défauts de surface ne sont pas spécifiées dans la présente partie de l’ISO 3290.
2 © ISO 2014 – Tous droits réservés

---------------------- Page: 6 ----------------------
ISO 3290-1:2014(F)

3.7.3
rugosité de surface
irrégularités de surface, relativement faiblement espacées, qui englobent habituellement les irrégularités
résultant du processus de fabrication mis en œuvre et/ou d’autres facteurs d’influence
Note 1 à l’article: Ces irrégularités sont considérées dans des limites définies conventionnellement, par exemple,
dans les limites de la longueur de base.
3.7.4
ondulation
irrégularités de surface présentant un écart aléatoire ou périodique par rapport à la sphère idéale
Note 1 à l’article: Par défaut une ondulation doit être évaluée comme une amplitude de vitesse.
Note 2 à l’article: En pratique, les composantes de l’ondulation sont discriminées à partir de la surface réelle par
un analyseur d’ondulation (filtres).
3.8
écart d’un lot de billes par rapport à la classe de bille
différence entre le diamètre moyen d’un lot de billes considéré et le diamètre nominal augmenté de la
classe de bille
[SOURCE: ISO 5593:1997, 05.04.10]
3.9
dureté
mesure de la résistance à la pénétration déterminée par une méthode d’essai appropriée
Note 1 à l’article: Pour les billes en acier, une telle méthode est généralement l’essai de dureté Rockwell.
3.10
diamètre moyen d’une bille
moyenne arithmétique entre le plus grand et le plus petit des diamètres isolés de la bille
[SOURCE: ISO 5593:
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.