ISO 23555-1:2022
(Main)Gas pressure safety and control devices for use in gas transmission, distribution and installations for inlet pressures up to and including 10 MPa — Part 1: General requirements
Gas pressure safety and control devices for use in gas transmission, distribution and installations for inlet pressures up to and including 10 MPa — Part 1: General requirements
This document specifies generic safety, constructional, performance, testing and documentation requirements for high pressure controls for use in gas transmission, distribution and installations (hereafter referred to as controls). This document is applicable to controls with operating pressures greater than 500 kPa (5 bar) and up to and including 10 MPa (100 bar) and nominal size up to DN 400 for use with fuel gases as natural gas, manufactured gas, biomethane or liquefied petroleum gas (LPG) in commercial, industrial installations, including fuel gas infrastructures. The test methods given in this document are intended for product type test, routine tests and batch surveillance tests. This document is not applicable to: — controls upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters; — controls designed with declared maximum capacity ≤200 m3/h (normal conditions) and declared maximum inlet pressure ≤500 kPa (5 bar), to be incorporated into pressure control systems used in service lines (pipework from the main pipework in a gas infrastructure to the point of delivery of the gas); — industrial process control valves, such as IEC 60534; — controls used in aggressive/sour gas environments (gas environments containing water and H2S are considered sour) or severely corrosive conditions; — controls in service conditions with renewables (e.g. H2NG with hydrogen more than 10 %) and/or waste gases (e.g. biogas, etc.), if additional information is not provided (e.g. contaminant, liquid, etc.).
Dispositifs de commande et de sécurité de la pression de gaz destinés à être utilisés dans les installations de transport, de distribution et de stockage de gaz pour des pressions en entrée jusqu'à 10 MPa inclus — Partie 1: Exigences générales
General Information
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 23555-1
First edition
2022-01
Gas pressure safety and control
devices for use in gas transmission,
distribution and installations for
inlet pressures up to and including 10
MPa —
Part 1:
General requirements
Reference number
ISO 23555-1:2022(E)
© ISO 2022
---------------------- Page: 1 ----------------------
ISO 23555-1:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 23555-1:2022(E)
Contents Page
Foreword . vi
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms, definitions, symbols and abbreviated terms . 3
3.1 Terms and definitions . 3
3.1.1 General terms . 3
3.1.2 Terms related to components . 5
3.1.3 Terms related to components of functional performance. 6
3.1.4 Terms related to design and tests . 8
3.2 Symbols and abbreviated terms . 9
4 Classification .10
4.1 General . 10
4.2 Temperature classes . 10
4.3 Strength types . 11
5 Materials .11
5.1 General . 11
5.2 Requirements . 11
5.2.1 Requirements for metallic materials . 11
5.2.2 Requirements for non-metallic materials .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.