iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN IEC 61970-302:2024

(Main)

Energy management system application program interface (EMS-API) - Part 302: Common information model (CIM) dynamics

Energy management system application program interface (EMS-API) - Part 302: Common information model (CIM) dynamics

IEC 61970-302:2024 specifies a Dynamics package which contains part of the CIM to support the exchange of models between software applications that perform analysis of the steady-state stability (small-signal stability) or transient stability of a power system as defined by IEEE / CIGRE, Definition and classification of power system stability IEEE/CIGRE joint task force on stability terms and definitions. The model descriptions in this document provide specifications for each type of dynamic model as well as the information that needs to be included in dynamic case exchanges between planning/study applications. The scope of the CIM Dynamics package specified in this document includes: • standard models: a simplified approach to describing dynamic models, where models representing dynamic behaviour of elements of the power system are contained in predefined libraries of classes which are interconnected in a standard manner. Only the names of the selected elements of the models along with their attributes are needed to describe dynamic behaviour. • proprietary user-defined models: an approach providing users the ability to define the parameters of a dynamic behaviour model representing a vendor or user proprietary device where an explicit description of the model is not provided by this document. The same libraries and standard interconnections are used for both proprietary user-defined models and standard models. The behavioural details of the model are not documented in this document, only the model parameters. • A model to enable exchange of models’ descriptions. This approach can be used to describe user defined and standard models. • A model to enable exchange of simulation results. This second edition cancels and replaces the first edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The majority of issues detected in IEC 61970-302:2018 are addressed; b) IEEE 421.5-2016 on Excitation systems is fully covered; c) The IEEE turbine report from 2013 was considered and as a result a number of gas, steam and hydro turbines/governors are added; d) IEC 61400-27-1:2020 on wind turbines is fully incorporated; e) WECC Inverter-Based Resource (IBR) models, Hybrid STATCOM models and storage models are added; f) The user defined models are enhanced with a model which enables modelling of detailed dynamic model; g) A model to enable exchange of simulation results is added; h) The work on the HVDC models is not complete. The HVDC dynamics models are a complex domain in which there are no models that are approved or widely recognised on international level, i.e. there are only project-based models. At this stage IEC 61970-302:2022 only specifies some general classes. However, it is recognised that better coverage of HVDC will require a further edition of this document; i) Models from IEEE 1547-2018 "IEEE Standard for Interconnection and Interoperability of Distributed Energy Resources with Associated Electric Power Systems Interfaces" are added. j) Statements have been added to certain figures, tables, schemas, and enumerations throughout the document that indicate that they are reproduced with the permission of the UCA International User Group (UCAIug). These items are derived from the CIM.

Schnittstelle für Anwendungsprogramme für Energiemanagementsysteme (EMS-API) - Teil 302: Allgemeines Informationsmodell (CIM) Dynamik

Interface de programmation d'application pour système de gestion d'énergie (EMS-API) - Partie 302: Régimes dynamiques de modèle d'information commun (CIM)

IEC 61970-302:2024 spécifie un paquetage dynamique (Dynamics) contenant des extensions du modèle d'information commun (CIM). Il s'agit d'assurer l'échange des modèles entre les applications logicielles qui procèdent à l'analyse de la stabilité en régime établi (stabilité en petits signaux) ou de la stabilité transitoire d'un système de puissance comme cela est défini dans le document Definition and classification of power system stability (Définition et classification de la stabilité des systèmes de puissance) du groupe de travail commun IEEE/CIGRE sur les termes et définitions relatifs à la stabilité. Les descriptions de modèles indiquées dans le présent document donnent des spécifications pour chaque type de modèle dynamique, ainsi que des informations qui doivent être incluses dans les échanges de cas dynamiques entre les applications de planification/d'étude. Le domaine d'application du paquetage CIM Dynamics spécifié dans le présent document inclut: • des modèles normalisés: une approche simplifiée qui vise à décrire des modèles dynamiques, les modèles représentant le comportement dynamique des éléments du système de puissance qui sont contenus dans des bibliothèques prédéfinies de classes interconnectées de manière normalisée. Seuls les noms des éléments sélectionnés des modèles, accompagnés de leurs attributs, sont nécessaires à la description du comportement dynamique; • des modèles propriétaires définis par l'utilisateur: approche qui donne à l'utilisateur la possibilité de définir les paramètres d'un modèle de comportement dynamique représentant le dispositif propriétaire d'un fournisseur ou d'un utilisateur lorsque le présent document ne donne pas de description explicite du modèle. Les mêmes bibliothèques et interconnexions normalisées sont utilisées tant pour les modèles propriétaires définis par l'utilisateur que pour les modèles normalisés. Les détails comportementaux du modèle ne sont pas documentés dans le présent document, seuls les paramètres du modèle le sont; • un modèle d'échange des descriptions des modèles. Cette approche peut être utilisée pour décrire les modèles définis par l'utilisateur et les modèles normalisés; • un modèle d'échange des résultats de simulation. Cette deuxième édition annule et remplace la première édition parue en 2018. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) la majeure partie des problèmes détectés dans l'IEC 61970-302:2018 ont été résolus; b) l’IEEE 421.5-2016 relative aux systèmes d'excitation est intégralement couverte; c) le rapport IEEE sur les turbines publié en 2013 a été pris en considération et, à ce titre, un certain nombre de turbines/régulateurs à vapeur, à gaz et hydrauliques ont été ajoutés; d) l’IEC 61400-27-1:2020 relative aux éoliennes est totalement intégrée; e) des modèles de ressources fondées sur les onduleurs (IBR - Inverter based Resource), des modèles STATCOM hybrides et des modèles de stockage WECC ont été ajoutés; f) les modèles définis par l'utilisateur ont été améliorés avec un modèle de modélisation de modèle dynamique détaillé; g) un modèle d'échange des résultats de simulation a été ajouté; h) le travail réalisé sur les modèles CCHT n'est pas terminé. Les modèles de régimes dynamiques CCHT sont un domaine complexe dans lequel aucun modèle n'est approuvé ou ne fait l'objet d'un consensus au

Aplikacijski programski vmesnik za sistem upravljanja z energijo (EMS-API) - 302. del: Skupni informacijski model (CIM) za dinamiko (IEC 61970-302:2024)

General Information

Status
Published
Publication Date
14-Mar-2024
ICS
33.200 - Telecontrol. Telemetering
Technical Committee
CLC/TC 57 - Power systems management and associated information exchange
Drafting Committee
IEC/TC 57 - IEC_TC_57
Current Stage
6060 - Document made available - Publishing
Start Date
15-Mar-2024
Completion Date
15-Mar-2024
Mandate
M/490 - Standardisation mandate to the European Standardisation Organisations (ESOs) to support European Smart Grid deployment
Ref Project
SIST EN IEC 61970-302:2024 - Energy management system application program interface (EMS-API) - Part 302: Common information model (CIM) dynamics (IEC 61970-302:2024)

Relations

Replaces
EN IEC 61970-302:2018 - Energy management system application program interface (EMS-API) - Part 302: Common information model (CIM) dynamics
Effective Date
27-Apr-2021

Buy Standard

EN IEC 61970-302:2024 - BARVEEN IEC 61970-302:2024 - BARVE
PreviousNext
Standard
EN IEC 61970-302:2024 - BARVE
English language
894 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61970-302:2024
01-maj-2024
Aplikacijski programski vmesnik za sistem upravljanja z energijo (EMS-API) - 302.
del: Skupni informacijski model (CIM) za dinamiko (IEC 61970-302:2024)
Energy management system application program interface (EMS-API) - Part 302:
Common information model (CIM) dynamics (IEC 61970-302:2024)
Schnittstelle für Anwendungsprogramme für Energiemanagementsysteme (EMS-API) -
Teil 302: Allgemeines Informationsmodell (CIM) Dynamik (IEC 61970-302:2024)
Interface de programmation d'application pour système de gestion d'énergie (EMS-API) -
Partie 302: Régimes dynamiques de modèle d'information commun (CIM) (IEC 61970-
302:2024)
Ta slovenski standard je istoveten z: EN IEC 61970-302:2024
ICS:
29.240.30 Krmilna oprema za Control equipment for electric
elektroenergetske sisteme power systems
35.200 Vmesniška in povezovalna Interface and interconnection
oprema equipment
SIST EN IEC 61970-302:2024 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61970-302:2024

---------------------- Page: 2 ----------------------
SIST EN IEC 61970-302:2024


EUROPEAN STANDARD EN IEC 61970-302

NORME EUROPÉENNE

EUROPÄISCHE NORM March 2024
ICS 33.200 Supersedes EN IEC 61970-302:2018
English Version
Energy management system application program interface
(EMS-API) - Part 302: Common information model (CIM)
dynamics
(IEC 61970-302:2024)
Interface de programmation d'application pour système de Schnittstelle für Anwendungsprogramme für
gestion d'énergie (EMS-API) - Partie 302: Régimes Energiemanagementsysteme (EMS-API) - Teil 302:
dynamiques de modèle d'information commun (CIM) Allgemeines Informationsmodell (CIM) Dynamik
(IEC 61970-302:2024) (IEC 61970-302:2024)
This European Standard was approved by CENELEC on 2024-03-06. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61970-302:2024 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61970-302:2024
EN IEC 61970-302:2024 (E)
European foreword
The text of document 57/2620/FDIS, future edition 2 of IEC 61970-302, prepared by IEC/TC 57
"Power systems management and associated information exchange" was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN IEC 61970-302:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2024-12-06
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-03-06
document have to be withdrawn
This document supersedes EN IEC 61970-302:2018 and all of its amendments and corrigenda (if
any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61970-302:2024 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the st
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 60870-5-104:2006/A1:2016/AC:2023-09(Corrigendum)
Telecontrol equipment and systems - Part 5-104: Transmission protocols - Network access for IEC 60870-5-101 using standard transport profiles
SIST EN 60870-5-104:2007/A1:2017/AC:2024
  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62351-3:2023(Main)
Power systems management and associated information exchange - Data and communications security - Part 3: Communication network and system security - Profiles including TCP/IP
SIST EN IEC 62351-3:2023

IEC 62351-3:2023 specifies how to provide confidentiality, integrity protection, and message level authentication for protocols that make use of TCP/IP as a message transport layer and utilize Transport Layer Security when cyber-security is required. This may relate to SCADA and telecontrol protocols, but also to additional protocols if they meet the requirements in this document. IEC 62351-3 specifies how to secure TCP/IP-based protocols through constraints on the specification of the messages, procedures, and algorithms of Transport Layer Security (TLS) (TLSv1.2 defined in RFC 5246, TLSv1.3 defined in RFC 8446). In the specific clauses, there will be subclauses to note the differences and commonalities in the application depending on the target TLS version. The use and specification of intervening external security devices (e.g., "bump-in-the-wire") are considered out-of-scope. In contrast to previous editions of this document, this edition is self-contained in terms of completely defining a profile of TLS. Hence, it can be applied directly, without the need to specify further TLS parameters, except the port number, over which the communication will be performed. Therefore, this part can be directly utilized from a referencing standard and can be combined with further security measures on other layers. Providing the profiling of TLS without the need for further specifying TLS parameters allows declaring conformity to the described functionality without the need to involve further IEC 62351 documents. This document is intended to be referenced as a normative part of other IEC standards that have the need for providing security for their TCP/IP-based protocol exchanges under similar boundary conditions. However, it is up to the individual protocol security initiatives to decide if this document is to be referenced. The document also defines security events for specific conditions, which support error handling, security audit trails, intrusion detection, and conformance testing. Any action of an organization in response to events to an error condition described in this document are beyond the scope of this document and are expected to be defined by the organization’s security policy. This document reflects the security requirements of the IEC power systems management protocols. Should other standards bring forward new requirements, this document may need to be revised. This second edition cancels and replaces the first edition published in 2014, Amendment 1:2018 and Amendment 2:2020. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Inclusion of the TLSv1.2 related parameter required in IEC 62351-3 Ed.1.2 to be specified by the referencing standard. This comprises the following parameter: • Mandatory TLSv1.2 cipher suites to be supported. • Specification of session resumption parameters. • Specification of session renegotiation parameters. • Revocation handling using CRL and OCSP. • Handling of security events. b) Inclusion of a TLSv1.3 profile to be applicable for the power system domain in a similar way as for TLSv1.2 session.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62351-9:2023(Main)
Power systems management and associated information exchange - Data and communications security - Part 9: Cyber security key management for power system equipment
SIST EN IEC 62351-9:2023

IEC 62351-9:2023 specifies cryptographic key management, primarily focused on the management of long-term keys, which are most often asymmetric key pairs, such as public-key certificates and corresponding private keys. As certificates build the base this document builds a foundation for many IEC 62351 services (see also Annex A). Symmetric key management is also considered but only with respect to session keys for group-based communication as applied in IEC 62351-6. The objective of this document is to define requirements and technologies to achieve interoperability of key management by specifying or limiting key management options to be used. This document assumes that an organization (or group of organizations) has defined a security policy to select the type of keys and cryptographic algorithms that will be utilized, which may have to align with other standards or regulatory requirements. This document therefore specifies only the management techniques for these selected key and cryptography infrastructures. This document assumes that the reader has a basic understanding of cryptography and key management principles. The requirements for the management of pairwise symmetric (session) keys in the context of communication protocols is specified in the parts of IEC 62351 utilizing or specifying pairwise communication such as: • IEC 62351-3 for TLS by profiling the TLS options • IEC 62351-4 for the application layer end-to-end security • IEC TS 62351-5 for the application layer security mechanism for IEC 60870-5-101/104 and IEEE 1815 (DNP3) The requirements for the management of symmetric group keys in the context of power system communication protocols is specified in IEC 62351-6 for utilizing group security to protect GOOSE and SV communication. IEC 62351-9 utilizes GDOI as already IETF specified group-based key management protocol to manage the group security parameter and enhances this protocol to carry the security parameter for GOOSE, SV, and PTP. This document also defines security events for specific conditions which could identify issues which might require error handling. However, the actions of the organisation in response to these error conditions are beyond the scope of this document and are expected to be defined by the organizations security policy. In the future, as public-key cryptography becomes endangered by the evolution of quantum computers, this document will also consider post-quantum cryptography to a certain extent. Note that at this time being no specific measures are provided. This second edition cancels and replaces the first edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Certificate components and verification of the certificate components have been added; b) GDOI has been updated to include findings from interop tests; c) GDOI operation considerations have been added; d) GDOI support for PTP (IEEE 1588) support has been added as specified by IEC/IEEE 61850-9-3 Power Profile; e) Cyber security event logging has been added as well as the mapping to IEC 62351-14; f) Annex B with background on utilized cryptographic algorithms and mechanisms has been added.

  • Standard
    147 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62488-2:2017/AC:2023-03(Corrigendum)
Power line communication systems for power utility applications - Part 2: Analogue power line carrier terminals or APLC
SIST EN 62488-2:2017/AC:2023
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62351-5:2023(Main)
Power systems management and associated information exchange - Data and communications security - Part 5: Security for IEC 60870-5 and derivatives
SIST EN IEC 62351-5:2023

This part of IEC 62351 defines the application authentication mechanism (A-profile) specifying messages, procedures and algorithms for securing the operation of all protocols based on or derived from IEC 60870-5: Telecontrol Equipment and Systems - Transmission Protocols. This Standard applies to at least those protocols listed in Table 1. [Table 1] The initial audience for this International Standard is intended to be the members of the working groups developing the protocols listed in Table 1. For the measures described in this standard to take effect, they must be accepted and referenced by the specifications for the protocols themselves. This document is written to enable that process. The working groups in charge of take this standard to the specific protocols listed in Table 1 may choose not to do so. The subsequent audience for this specification is intended to be the developers of products that implement these protocols. Portions of this standard may also be of use to managers and executives in order to understand the purpose and requirements of the work. This document is organized working from the general to the specific, as follows: - Clauses 2 through 4 provide background terms, definitions, and references. - Clause 5 describes the problems this specification is intended to address. - Clause 6 describes the mechanism generically without reference to a specific protocol. - Clauses 7 and 8 describe the mechanism more precisely and are the primary normative part of this specification. - Clause 9 define the interoperability requirements for this authentication mechanism. - Clause 10 describes the requirements for other standards referencing this specification Unless specifically labelled as informative or optional, all clauses of this specification are normative.

  • Standard
    126 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61970-401:2022(Main)
Energy management system application program interface (EMS-API) - Part 401: Profile framework
SIST EN IEC 61970-401:2022

This document describes how IEC 61970-450 (all parts), IEC 61970-600 (all parts) profile specifications are structured and created. Profile specifications describe a subset of the Canonical CIM dedicated to a specific data exchange. The Canonical CIM is described in IEC 61970-300 (all parts) as well as in IEC 61968-11. Rules for creation or extension of Canonical CIM are outside the scope of this document. This document specifies the structure of a profile specification and the rules for selecting subsets of information from the Canonical CIM. It standardizes the operations used to create the profile elements from the Canonical CIM. As Canonical CIM is described in UML the operations are described in terms of UML classes, attributes, and roles. It is possible to map UML to RDFS or OWL, so any of the languages UML, RDFS or OWL can be used to describe the created profiles. Specification of languages (UML, RDFS or OWL) used to describe profiles as well as how profiles are presented and edited in user interfaces are outside the scope of this document. Languages used to describe profiles are specified in other specifications. Relevant specifications are referenced in Clause 2. UML supports adding free text that describes further restrictions on UML constructs, e.g. classes, attribute values, association roles and cardinalities. Languages such as OCL and SHACL are dedicated to describing constraints. OCL is used to describe constraints for object data described in UML while SHACL is used to describe constraints on graph data described by RDFS or OWL. OCL is within the scope of this document, but SHACL is not. This document supports profiles describing data exchanged as CIMXML datasets or messages. The exchange format within the scope is in accordance with IEC 61970-552 but other formats are possible. Tool interoperability and serialisation formats are outside the scope of this document.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62325-451-8:2022(Main)
Framework for energy market communications - Part 451-8: HVDC Scheduling process, contextual and assembly models for European style market
SIST EN IEC 62325-451-8:2022

IEC 62325-451-8:2022 specifies a UML package for the HVDC Link scheduling business process and its associated document contextual models, assembly models and XML schemas for use within the European style electricity markets. This part of IEC 62325 is based on the European style market contextual model (IEC 62325-351). The business process covered by this part of IEC 62325 is described in Subclause 5.3. The relevant aggregate core components (ACCs) defined in IEC 62325-351 have been contextualised into aggregated business information entities (ABIEs) to satisfy the requirements of the European style market HVDC Link scheduling business process.

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61850-5:2013/A1:2022(Amendment)
Communication networks and systems for power utility automation - Part 5: Communication requirements for functions and device models
SIST EN 61850-5:2013/A1:2022

PUBLICATION EXPECTED BY 2022-04-27

  • Amendment
    80 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61970-301:2020/A1:2022(Amendment)
Energy management system application program interface (EMS-API) - Part 301: Common information model (CIM) base
SIST EN IEC 61970-301:2020/A1:2022
  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61968-100:2022(Main)
Application integration at electric utilities - System interfaces for distribution management - Part 100: IEC Implementation profiles for application integration
SIST EN IEC 61968-100:2022

1.1 General This International Standard is Part 100 of IEC 61968. It defines how messages may be exchanged between co-operating systems in order to facilitate the transfer of application-specific data. Such application-specific data include but are not limited to the message payloads defined in IEC 61968 (Parts 3-9 and Part 13), IEC 61970 and IEC 62325. 1.2 About This International Standard This International Standard provides normative definitions for: - a set of message archetypes (clause 5); - a set of message exchange patterns that both sending and receiving systems are expected to implement (clause 6); - the exact format of the messages that are to be transmitted over the various integration technologies including a precise description of the information that each message must contain (clause 7); - a set of constraints and conventions to which applications must adhere in order to facilitate message exchange using IEC 61968-100 (clause 8); - the details of how IEC 61968-100 messages should be implemented using various underlying transport mechanisms (clause 9). 1.3 What is not covered by this International Standard Security considerations lie outside the scope of IEC 61968-100. This document defers to the IEC 62351 series for definitions and practices relating to the secure transmission of messages. 1.4 Future Considerations 1.4.1 Choice of Encoding Mechanisms IEC 61968-100:2021 prescribes XML as the normative encoding mechanism for all messages defined by this International Standard. Future editions of IEC 61968-100 may specify additional normative encoding methods including support for IEC 62361-104. The latter defines encodings to facilitate the exchange of information in the form of JSON documents whose semantics are defined by the IEC CIM and whose syntax is defined by an IETF JSON schema. 1.4.2 Choice of Web Service Technologies IEC 61968-100:2021 provides normative definitions for the use of SOAP Web Services (clause 9.2) and Java Messaging Service (clause 9.3) for the transport of messages. Future editions of IEC 61968-100 may specify additional normative web service technologies such as REST.

  • Standard
    251 pages
    English language
    sale 10% off
    e-Library read for
    1 day