EN 61019-2:2005

SLOVENSKI SIST EN 61019-1:2005

STANDARD
december 2005
Resonatorji za površinske akustične valove – 1. del: Generična specifikacija
(IEC 61019-1:2004)
Surface acoustic wave (SAW) resonators – Part 1: Generic specification (IEC
61019-1:2004)
ICS 31.140 Referenčna številka
SIST EN 61019-1:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 61019-2
NORME EUROPÉENNE
EUROPÄISCHE NORM June 2005

ICS 31.140 Supersedes EN 61019-2:1997


English version


Surface acoustic wave (SAW) resonators
Part 2: Guide to the use
(IEC 61019-2:2005)


Résonateurs à ondes acoustiques  Oberflächenwellenresonatoren
de surface (OAS) (OFW-Resonatoren)
Partie 2: Guide d'emploi Teil 2: Leitfaden für die Anwendung
(CEI 61019-2:2005) (IEC 61019-2:2005)






This European Standard was approved by CENELEC on 2005-06-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 61019-2:2005 E

---------------------- Page: 2 ----------------------

EN 61019-2:2005 - 2 -
Foreword
The text of document 49/714/FDIS, future edition 2 of IEC 61019-2, prepared by IEC TC 49,
Piezoelectric and dielectric devices for frequency control and selection, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61019-2 on 2005-06-01.
This European Standard supersedes EN 61019-2:1997.
The main changes with respect to EN 61019-2:1997 are listed below:
– at the end of 5.1, the edge reflector has been added. Its reference literature has been inserted in
the bibliography;
– in Table 1, the propagation properties of LiNbO3 (64° Y) have been added;
– in Table 3, the clause and subclause numbers have been corrected in order to be consistent with
EN 61019-1:2005.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-03-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-06-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61019-2:2005 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 61019-2:2005
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 61019-1 2004 Surface acoustic wave (SAW) resonators EN 61019-1 2005
Part 1: Generic specification

IEC 61019-3 1991 Part 3: Standard outlines and lead - -
connections

---------------------- Page: 4 ----------------------

INTERNATIONAL IEC


STANDARD 61019-2





Second edition
2005-05


Surface acoustic wave (SAW) resonators –
Part 2:
Guide to the use

 IEC 2005  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
Intern
...