EN 61837-4:2015
(Main)Surface mounted piezoelectric devices for frequency control and selection - Standard outlines and terminal lead connections - Part 4: Hybrid enclosure outlines
Surface mounted piezoelectric devices for frequency control and selection - Standard outlines and terminal lead connections - Part 4: Hybrid enclosure outlines
IEC 61837-4:2015 specifies the outline drawings and terminal lead connections for surface piezoelectric devices with hybrid enclosure outlines and is based on IEC 61240:2012 which standardized layout rules of outline drawings of surface-mounted device. This edition includes the following significant technical changes with respect to the previous edition: - Outline drawing is defined as one set of drawings consisting of four views, which are the view from above, the front view, the view from the right, and the view from below, instead of one set consisting of three views as provided in the previous edition. - The configurations of the enclosures were revised as shown in Table 1.
Oberflächenmontierbare piezoelektrische Bauteile zur Frequenzstabilisierung und -selektion - Norm-Gehäusemaße und Anschlüsse - Teil 4: Hybridgehäuse
Dispositifs piézoélectriques à montage en surface pour la commande et le choix de la fréquence - Encombrements normalisés et connexions des sorties - Partie 4: Encombrements des enveloppes hybrides
L'IEC 61837-4:2015 spécifie les dessins d'encombrement et les connexions des sorties pour les dispositifs piézoélectriques à montage en surface avec les encombrements d'enveloppes hybrides, et est fondée sur l'IEC 61240:2012, qui a normalisé les règles de tracé des dessins d'encombrement des dispositifs à montage en surface. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - Le dessin d'encombrement est défini comme un ensemble de dessins composé de quatre vues, à savoir la vue de dessus, la vue de face, la vue de droite et la vue de dessous, à la place de l'ensemble des trois vues prévu dans la version précédente. - Les configurations des enveloppes ont été révisées comme indiqué au Tableau 1.
Površinsko nameščeni piezoelektrični elementi za stabilizacijo in izbiranje frekvence - Standardne mere in priključni izvodi - 4. del: Mere hibridnega okrova
Ta del standarda IEC 61837 določa tehnične risbe in priključne izvode za površinske piezoelektrične elemente s hibridnimi okrovi in je osnovan na standardu IEC 61240:2012, ki je standardiziral osnovna pravila tehničnih risb površinsko montiranih naprav.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 61837-4:2015
01-september-2015
1DGRPHãþD
SIST EN 61837-4:2005
3RYUãLQVNRQDPHãþHQLSLH]RHOHNWULþQLHOHPHQWL]DVWDELOL]DFLMRLQL]ELUDQMH
IUHNYHQFH6WDQGDUGQHPHUHLQSULNOMXþQLL]YRGLGHO 0HUHKLEULGQHJDRNURYD
Surface mounted piezoelectric devices for frequency control and selection - Standard
outline and terminal lead connections - Part 4: Hybrid enclosure outline
Oberflächenmontierbare piezoelektrische Bauteile zur Frequenzstabilisierung und -
selektion - Norm-Gehäusemaße und Anschlüsse - Teil 4: Hybridgehäuse
Dispositifs piézoélectriques à montage en surface pour la commande et le choix de la
fréquence - Encombrements normalisés et connexions des sorties - Partie 4:
Encombrements des enveloppes hybrides
Ta slovenski standard je istoveten z: EN 61837-4:2015
ICS:
31.140 3LH]RHOHNWULþQHLQ Piezoelectric and dielectric
GLHOHNWULþQHQDSUDYH devices
SIST EN 61837-4:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 61837-4:2015
---------------------- Page: 2 ----------------------
SIST EN 61837-4:2015
EUROPEAN STANDARD EN 61837-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2015
ICS 31.140 Supersedes EN 61837-4:2004
English Version
Surface mounted piezoelectric devices for frequency control and
selection - Standard outlines and terminal lead connections -
Part 4: Hybrid enclosure outlines
(IEC 61837-4:2015)
Dispositifs piézoélectriques à montage en surface pour la Oberflächenmontierbare piezoelektrische Bauteile zur
commande et le choix de la fréquence - Encombrements Frequenzstabilisierung und -selektion - Norm-
normalisés et connexions des sorties - Gehäusemaße und Anschlüsse -
Partie 4: Encombrements des enveloppes hybrides Teil 4: Hybridgehäuse
(IEC 61837-4:2015) (IEC 61837-4:2015)
This European Standard was approved by CENELEC on 2015-05-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61837-4:2015 E
---------------------- Page: 3 ----------------------
SIST EN 61837-4:2015
EN 61837-4:2015 - 2 -
Foreword
The text of document 49/1117/FDIS, future edition 2 of IEC 61837-4, prepared by
IEC/TC 49 "Piezoelectric, dielectric and electrostatic devices and associated materials for frequency
control, selection and detection" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 61837-4:2015.
The following dates are fixed:
• latest date by which the document has to be (dop) 2016-02-01
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2018-05-01
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 61837-4:2004.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61837-4:2015 was approved by CENELEC as a European
Standard without any modification.
---------------------- Page: 4 ----------------------
SIST EN 61837-4:2015
- 3 - EN 61837-4:2015
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.