Environmental testing - Part 2-2: Tests - Test B: Dry heat

Deals with dry heat tests applicable both to heat-dissipating and non heat-dissipating specimens. For non heat-dissipating specimens, Tests Bb and Bd do not deviate essentially from earlier issues. The object of the dry heat test is limited to the determination of the ability of components, equipment or other articles to be used, transported or stored at high temperature. These dry heat tests do not enable the ability of specimens to withstand or operate during the temperature variations to be assessed. In this case, it would be necessary to use IEC 60068-2-14 Test N: Change of temperature. The dry heat tests are subdivided as follows: Dry heat test for non heat-dissipating specimens - with gradual change of temperature, Bb. Dry heat tests for heat-dissipating specimens - with gradual change of temperature, Bd; - with gradual change of temperature, specimen powered throughout, Be. The procedures given in this standard are normally intended for specimens that achieve temperature stability during the performance of the test procedure. The main changes from the previous edition are as follows: Tests Ba and Bc have been deleted since they were more severe tests than Test Nb, IEC 60068-2-14: Change of temperature. Secondly it was considered justified to delete the 3 % value on the temperature difference between the chamber air and the wall temperatures. Thirdly it is proposed that the test specimen be powered throughout the test where required; and, finally, the annexes have been removed. Has the status of a basic safety publication in accordance with IEC Guide 104.

Umgebungseinflüsse - Teil 2-2: Prüfverfahren - Prüfung B: Trockene Wärme

Essais d'environnement - Partie 2-2: Essais - Essai B: Chaleur sèche

Traite des essais de chaleur sèche applicables à la fois aux spécimens dissipant de l'énergie et à ceux ne dissipant pas d'énergie. Les essais Bb et Bd destinés à des spécimens ne dissipant pas d'énergie ne présentent pas de modifications importantes par rapport aux éditions précédentes. Le but de l'essai de chaleur sèche se limite à la détermination de l'aptitude des composants, équipements ou autres articles à être utilisés, transportés ou stockés à haute température. Ces essais de chaleur sèche ne permettent pas de vérifier l'aptitude des spécimens à subir ou à fonctionner pendant les variations de température. Dans ce cas, il serait nécessaire d'utiliser l'essai N de la CEI 60068-2-14: Variations de température. Les essais de chaleur sèche se subdivisent de la façon suivante: Essai de chaleur sèche pour spécimens ne dissipant pas d'énergie - avec variation lente de la température, Bb. Essais de chaleur sèche pour spécimens dissipant de l'énergie - avec variation lente de la température, Bd; - avec variation lente de la température, pour les spécimens dissipant partout, Be. La procédure décrite dans cette norme est normalement prévue pour les spécimens qui atteignent la stabilité thermique pendant le déroulement de l'essai. Les principaux changements par rapport à l'édition précédente sont les suivants: Les essais Ba et Bc ont été retirés puisqu'ils étaient plus sévères que l'essai Nb de la CEI 60068 2 14: Variations de température. Deuxièmement, il a été considéré justifié de supprimer la valeur de 3 % sur la différence de température entre l'air de la chambre d'essai et les températures des parois. Troisièmement, il est proposé et non plus exigé que le spécimen d'essai soit mis en fonctionnement durant l'essai; et, pour finir, les annexes ont été retirées. A le statut d'une publication fondamentale de sécurité, conformément au Guide CEI 104

Okoljsko preskušanje - 2-2. del: Preskusi - Preskusi B: Suha vročina (IEC 60068-2-2:2007)

General Information

Status
Published
Publication Date
20-Sep-2007
Withdrawal Date
31-Aug-2010
Current Stage
6060 - Document made available - Publishing
Start Date
21-Sep-2007
Completion Date
21-Sep-2007

Relations

Buy Standard

Standard
EN 60068-2-2:2008
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 60068-2-2:2005
English language
26 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60068-2-2:2008
01-januar-2008
1DGRPHãþD
SIST EN 60068-2-2:2002 + A1:2002
2NROMVNRSUHVNXãDQMHGHO3UHVNXVL3UHVNXVL%6XKDYURþLQD ,(&

Environmental testing - Part 2-2: Tests - Tests B: Dry heat
Umgebungseinflüsse - Teil 2-2: Prüfverfahren - Prüfung B: Trockene Wärme
Essais d'environnement - Partie 2-2: Essais - Essai B: Chaleur seche
Ta slovenski standard je istoveten z: EN 60068-2-2:2007
ICS:
19.040 Preskušanje v zvezi z Environmental testing
okoljem
SIST EN 60068-2-2:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 60068-2-2

NORME EUROPÉENNE
September 2007
EUROPÄISCHE NORM

ICS 19.040 Supersedes EN 60068-2-2:1993 + A1:1993 + A2:1994


English version


Environmental testing -
Part 2-2: Tests -
Test B: Dry heat
(IEC 60068-2-2:2007)


Essais d'environnement -  Umgebungseinflüsse -
Partie 2-2: Essais - Teil 2-2: Prüfverfahren -
Essai B: Chaleur sèche Prüfung B: Trockene Wärme
(CEI 60068-2-2:2007) (IEC 60068-2-2:2007)




This European Standard was approved by CENELEC on 2007-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60068-2-2:2007 E

---------------------- Page: 2 ----------------------

EN 60068-2-2:2007 - 2 -
Foreword
The text of document 104/412/FDIS, future edition 5 of IEC 60068-2-2, prepared by IEC TC 104,
Environmental conditions, classification and methods of test, was submitted to the IEC-CENELEC parallel
vote and was approved by CENELEC as EN 60068-2-2 on 2007-09-01.
This European Standard supersedes EN 60068-2-2:1993 + A1:1993 + A2:1994.
The main changes from EN 60068-2-2:1993 + A1:1993 + A2:1994 are as follows: Tests Ba and Bc have
been deleted since they were more severe tests than Test Nb, EN 60068-2-14: Change of temperature.
Secondly it was considered justified to delete the 3 % value on the temperature difference between the
chamber air and the wall temperatures. Thirdly it is proposed that the test specimen be powered
throughout the test where required; and, finally, the annexes have been removed.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2008-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60068-2-2:2007 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 60068-2-2:2007
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

1)
IEC 60068-1 1988 Environmental testing - EN 60068-1 1994
Part 1: General and guidance


2) 3)
IEC 60068-3-1 - Environmental testing - EN 60068-3-1 1999
Part 3: Background information -
Section One: Cold and dry heat tests


2) 3)
IEC 6
...

SLOVENSKI oSIST prEN 60068-2-2:2005

PREDSTANDARD
julij 2005
Okoljsko preskušanje – 2-2. del: Preskusi – Preskusi B: Suha vročina
Environmental testing – Part 2-2: Tests – Tests B: Dry heat
ICS 19.040 Referenčna številka
oSIST prEN 60068-2-2:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
104/371/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJET DE COMITÉ POUR VOTE (CDV)
Project number IEC 60068-2-2 Ed. 5.0
Numéro de projet

Date of circulation Closing date for voting (Voting
IEC/TC or SC:
104
Date de diffusion mandatory for P-members)
CEI/CE ou SC:

Date de clôture du vote (Vote
2005-05-06
obligatoire pour les membres (P))
2006-10-07
Titre du CE/SC:    TC/SC Title: Environmental Conditions,
classification and methods of test
Secretary: Alf Olsson, Sweden
Secrétaire:
Also of interest to the following committees Supersedes document
Intéresse également les comités suivants Remplace le document
Almost every product related IEC Committee 104/317/CD – 104/370/MCR
Functions concerned
Fonctions concernées
Safety EMC Environment Quality assurance
Sécurité
CEM Environnement Assurance qualité
CE DOCUMENT EST TOUJOURS À L'ÉTUDE ET SUSCEPTIBLE DE THIS DOCUMENT IS STILL UNDER STUDY AND SUBJECT TO CHANGE. IT
MODIFICATION. IL NE PEUT SERVIR DE RÉFÉRENCE. SHOULD NOT BE USED FOR REFERENCE PURPOSES.
LES RÉCIPIENDAIRES DU PRÉSENT DOCUMENT SONT INVITÉS À RECIPIENTS OF THIS DOCUMENT ARE INVITED TO SUBMIT, WITH THEIR
PRÉSENTER, AVEC LEURS OBSERVATIONS, LA NOTIFICATION DES COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF
DROITS DE PROPRIÉTÉ DONT ILS AURAIENT ÉVENTUELLEMENT WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING
CONNAISSANCE ET À FOURNIR UNE DOCUMENTATION EXPLICATIVE. DOCUMENTATION.

Titre : Essais d'environnement - Partie 2-2: Title : Environmental testing – Part 2-2: Tests –
Essais - Essais B: Chaleur sèche Tests B: Dry Heat

Introductory note
The Maintenance Team, MT 16 of IEC TC 104 has reviewed this basic IEC Test at several meetings and over a long period of time. The work with the first
CD started in Helsinki, February 2002 and continued until the Lindenstruth meeting in April 2003 where it was decided to reformat both the style and the
nd
presentation. The comments received on the 2 CD was presented in Kyoto in November the same year but was only introduced in the draft for a CDV in
Massa Martana in October 2004. Although the MT realised that the basis for making major changes of the document was little it still felt it necessary to go
ahead with the changes announced in both CDs and in the relevant MCRs. Consequently MT 16 have deleted tests Ba and Bc since they were more
severe test than Test Nb, IEC 60068-2-14: Change of temperature.
Secondly it was considered justified to delete the 3% value on the temperature difference between the chamber air and the wall temperatures;
Thirdly it is proposed that the test specimen be powered throughout the test were required to and; finally the annexes are removed

Finally a message from the experts of TC 104:
When the revision of IEC 60068-2-1 and 60068-2-2 have been successfully concluded then MT 16 intends to review IEC 60068-3-1.

IF YOU CARE ABOUT THE WORK, THEN YOU SHOULD PARTICIPATE?
Either you come to us or we come to you.
IF YOU AGREE WITH WHAT WE ARE DOING? THEN YOU MUST CONTRIBUTE BY SENDING COMMENTS.
IF YOU DON’T CARE or DON’T AGREE and DON’T PARTICIPATE then there will soon be
NO ONE LEFT TO DO THE JOB FOR YOU.
This project was cancelled in October 2004, see SMB/2924/DL, prior to circulation of the compilation of
comments on 104/317/CD.
The comments are attached in Annex A for information.
ATTENTION ATTENTION

CDV soumis en parallèle au vote (CEI) Parallel IEC CDV/CENELEC Enquiry
et à l’enquête (CENELEC)

Copyright © 2005 International Electrotechnical Commission, IEC. All rights reserved. It is
permitted to download this electronic file, to make a copy and to print out the content for the sole
purpose of preparing National Committee positions. You may not copy or "mirror" the file or
printed version of the document, or any part of it, for any other purpose without permission in
writing from IEC.
FORM CDV (IEC) 2002-08-09

---------------------- Page: 2 ----------------------
– 2 – 104/371/CDV
IEC 60068-2-2 Ed.5.0 was cancelled in October 2004, see SMB/2924/DL, prior to circulation of the compilation of comments on 104/317/CD.
The comments are attached below for information.

Annex A
Date Document
2004 104/317/CD

National Clause/ Paragraph Type of comment COMMENTS Proposed change OBSERVATIONS OF THE SECRETARIAT
Committee Subclause Figure/Table (General/ on each comment submitted
Technical/Editorial)
FR1 0  The French National Committee Noted
supports the above document, and
submits the follow
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.