EN 603-3:2021
(Main)Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on dimensions and form
Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on dimensions and form
This document specifies the tolerances on dimensions and form of wrought aluminium and aluminium alloy forging stock.
It applies to extruded and rolled products.
Aluminium und Aluminiumlegierungen - Stranggepresstes oder gewalztes Schmiedevormaterial - Teil 3: Grenzabmaße und Formtoleranzen
Dieses Dokument legt die Grenzabmaße und Formtoleranzen von stranggepresstem oder gewalztem Aluminium-Schmiedevormaterial und Schmiedevormaterial von Aluminiumlegierungen fest.
Es ist anzuwenden für stranggepresste oder gewalzte Produkte.
Aluminium et alliages d'aluminium - Produits corroyés destinés à la forge - Partie 3: Tolérances sur dimensions et forme
Le présent document spécifie les tolérances sur dimensions et forme des produits corroyés en aluminium et en alliages d'aluminium destinés à la forge.
Il s'applique aux produits filés et laminés.
Aluminij in aluminijeve zlitine - Gneteni surovci za kovanje - 3. del: Odstopki mer in tolerance oblike
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 603-3:2021
01-november-2021
Nadomešča:
SIST EN 603-3:2002
Aluminij in aluminijeve zlitine - Gneteni surovci za kovanje - 3. del: Odstopki mer in
tolerance oblike
Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on
dimensions and form
Aluminium und Aluminiumlegierungen - Stranggepresstes oder gewalztes
Schmiedevormaterial - Teil 3: Grenzabmaße und Formtoleranzen
Aluminium et alliages d'aluminium - Produits corroyés destinés à la forge - Partie 3:
Tolérances sur dimensions et forme
Ta slovenski standard je istoveten z: EN 603-3:2021
ICS:
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 603-3:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 603-3:2021
---------------------- Page: 2 ----------------------
SIST EN 603-3:2021
EN 603-3
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2021
EUROPÄISCHE NORM
ICS 77.150.10 Supersedes EN 603-3:2000
English Version
Aluminium and aluminium alloys - Wrought forging stock -
Part 3: Tolerances on dimensions and form
Aluminium et alliages d'aluminium - Produits corroyés Aluminium und Aluminiumlegierungen -
destinés à la forge - Partie 3: Tolérances sur Stranggepresstes oder gewalztes Schmiedevormaterial
dimensions et forme - Teil 3: Grenzabmaße und Formtoleranzen
This European Standard was approved by CEN on 4 July 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 603-3:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 603-3:2021
EN 603-3:2021 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Dimensional ranges . 5
5 Alloys . 5
5.1 Chemical composition . 5
5.2 Alloy groups . 5
6 Tolerances on dimensions and form . 6
6.1 General. 6
6.2 Extruded round bar . 7
6.2.1 Diameter .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.