iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1226:1996

(Main)

Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection

Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection

This standard specifies a method for testing the ability of glass-reinforced thermosetting plastics (GRP) pipes to withstand specified levels of initial ring deflection without displaying surface damage and/or structural failure.

Kunststoff-Rohrleitungssysteme - Rohre aus glasfaserverstärkten duroplastischen Kunststoffen (GFK) - Verfahren zur Überprüfung der Anfangs-Ringverformbarkeit

Diese Norm legt ein Verfahren zur Prüfung der Widerstandsfähigkeit von Rohren aus glasfaserverstärkten duroplastischen Kunststoffen (GFK) gegenüber festgelegten Anfangs-Ringverformungen, ohne Auftreten von Oberflächenschädigung und/oder strukturellem Versagen, fest.

Systèmes de canalisations en plastique - Tubes en plastique thermodurcissables renforcé de verre (PRV) - Méthode d'essai pour établir la résistance à la déflexion annulaire initiale

Cette norme spécifie une méthode d'essai de la capacité des tubes en plastique thermodurcissable renforcés de verre (PRV) à résister à des niveaux spécifiés de déflexion annulaire initiale, sans apparition d'endommagement de surface et/ou de défaillance structurelle.

Cevni sistemi iz polimernih materialov - Cevi iz duromernih materialov, ojačenih s steklenimi vlakni (GRP) - Metoda za preskus in potrditev odpornosti proti začetni obodni deformaciji

General Information

Status
Withdrawn
Publication Date
18-Jun-1996
Withdrawal Date
02-Apr-2013
ICS
83.140.30 - Plastics pipes and fittings for non fluid use
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 14 - Systems of glass-reinforced thermosetting plastics for all applications - Polyester, epoxy and polyester resin based concrete
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
03-Apr-2013
Completion Date
03-Apr-2013
Directive
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
SIST EN 1226:1997 - Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection

Buy Standard

EN 1226:1997EN 1226:1997
PreviousNext
Standard
EN 1226:1997
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoff-Rohrleitungssysteme - Rohre aus glasfaserverstärkten duroplastischen Kunststoffen (GFK) - Verfahren zur Überprüfung der Anfangs-RingverformbarkeitSystemes de canalisations en plastique - Tubes en plastique thermodurcissables renforcé de verre (PRV) - Méthode d'essai pour établir la résistance a la déflexion annulaire initialePlastics piping systems - Glass-reinforced thermoset
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 16486-1:2023(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO 16486-1:2023)
SIST EN ISO 16486-1:2024

This document specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
This document establishes a calculation and design scheme on which to base the maximum operating pressure (MOP) of a PA-U piping system.
NOTE            For the purpose of this document the term gaseous fuels includes, for example, natural gas, methane, butane, propane, hydrogen, manufactured gas, biogas, and mixtures of these gases.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN ISO/TS 16486-7:2023(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 7: Assessment of conformity (ISO/TS 16486-7:2023)
SIST-TS CEN ISO/TS 16486-7:2023

This document gives guidance and requirements for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of the ISO 16486 series which are intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1    A basic test matrix in Annex B provides an overview of the testing scheme.
It is recommended for the manufacturer to have a management system such as ISO 9001[4] or equivalent.
NOTE 2    If certification is involved, certification bodies and inspection bodies operating according to ISO/IEC 17065 and ISO/IEC 17020 are considered to be competent.
In conjunction with the other parts of the ISO 16486 series (see Clause 2), this document is applicable to unplasticized polyamide (PA-U) piping systems intended to be buried and used for the supply of gaseous fuels. It is applicable to PA-U pipes, fittings and valves, as well as to their joints and to joints with components of other materials intended to be used under the following conditions:
a)    a maximum operating pressure (MOP) up to and including 18 bar[1] (the MOP is limited to 16 bar for CEN member countries, where ISO 16486-6 is replaced by CEN/TS 12007-6[1]);
b)    an operating temperature of 20 °C as the reference temperature.
NOTE 3    For operating temperatures different to 20 °C, derating coefficients can be used (see ISO 16486-6). CEN member countries use CEN/TS 12007-6[1] and ISO/TS 16486-7 (this document) as a basis, but they can also request additional requirements. For non-CEN member countries, information for dealing with special cases for PA-U can be found in ISO/TS 16486-7 (this document) and PPI TR-3.[7]
For mechanical fittings conforming to ISO 17885, guidance for assessment of conformity is not given in this document. When requested, a quality plan based on the tests mentioned can be set up in agreement between user and manufacturer.
The ISO 16486 series covers a range of maximum operating pressures and gives requirements concerning colours.
NOTE 4    It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Technical specification
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 14541-2:2022(Main)
Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 2: Recommendations for relevant characteristics
SIST-TS CEN/TS 14541-2:2022

This document provides guidance and information for drafting product standards to specify characteristics and test methods for the utilization of thermoplastics recyclates (PVC-U, PVC-C, PE, PP, ABS) in pipes, fittings and ancillaries for thermoplastics piping systems.
This document covers recyclates with an agreed specification from all sources.
NOTE 1   This document does not cover characteristics for reworked material.
NOTE 2   This document does not cover recycling processes (e.g. chemical or mechanical).
NOTE 3   This document does not define if recycled material can be used in a specific application. The possible use of recyclates will be defined in the applicable product standard.
This document provides guidance about the relevant characteristics to be included in the agreed specification for recyclates.
This document is applicable without prejudice to any existing legislation.
For the recycling process, the transport, the testing and the use of thermoplastics recyclates, National and/or European regulations (e.g. hygienic aspects) can apply.
NOTE 4   For example, threshold levels for substances of very high concern (SVHC) as defined in the REACH-legislation which can possibly be present in thermoplastic recyclates.

  • Technical specification
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14541-1:2022(Main)
Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary
SIST EN 14541-1:2022

This document specifies the general terms and definitions relevant for the utilization of thermoplastics recyclates in thermoplastics pipes, fittings and ancillaries for both pressure and non-pressure piping systems.
This document is intended to be used by specification writers in conjunction with CEN/TS 14541-2 when preparing normative documents under the scope of CEN/TC 155.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16486-4:2022(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 4: Valves (ISO 16486-4:2022)
SIST EN ISO 16486-4:2022

This document specifies the characteristics of valves made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PA-U pipes or fittings conforming to ISO 16486-2 and ISO 16486-3 respectively.
Valves made from material other than unplasticized polyamide designed for the supply of gaseous fuels conforming to the relevant standards are permitted to be used in PA-U piping systems according to the ISO 16486 series provided they have relevant PA-U connections for butt fusion or electrofusion ends (see ISO 16486-3). The component, i.e. the complete valve, is required to fulfil the requirements of this document.
This document also specifies the test parameters for the test methods it describes.
In conjunction with ISO 16486-1, ISO 16486-2, ISO 16486-3 and ISO 16486-5, this document is applicable to PA-U valves and their joints and to joints with components of PA-U and other materials intended to be used under the following conditions:
a) a maximum operating pressure (MOP) of up to and including 18 bar[1], or limited to 16 bar under regional CEN requirements, at a reference temperature of 20 °C for design purposes;
NOTE 1    For the purpose of this document and the references to ISO 8233, MOP is considered to be nominal pressure.
b) an operating temperature of −20 °C to 40 °C;
NOTE 2    For operating temperatures between 20 °C and 40 °C, derating coefficients are specified in ISO 16486-5.
This document covers valves for pipes with a nominal outside diameter, dn, ≤ 400 mm.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm².

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16486-5:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 5: Fitness for purpose of the system (ISO 16486-5:2021)
SIST EN ISO 16486-5:2021

This document specifies the requirements of fitness for purpose of unplasticized polyamide (PA-U) piping system, intended to be buried and used for the supply of gaseous fuels. It also specifies the definitions of electrofusion and butt fusion joints.
This document specifies the method of preparation of test piece joints and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
In conjunction with the other parts of ISO 16486, it is applicable to PA-U fittings, their joints and to joints with components of PA-U.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16486-2:2020(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 2: Pipes (ISO 16486-2:2020)
SIST EN ISO 16486-2:2020

This document specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series of standards is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, this document lays down dimensional characteristics and requirements for the marking of pipes.
Pipes conforming to this document are jointed typically by using mechanical, electrofusion or butt fusion techniques.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16486-3:2020(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 3: Fittings (ISO 16486-3:2020)
SIST EN ISO 16486-3:2020

This document specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486‑1, intended to be buried and used for the supply of gaseous fuels.
It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and requirements for the marking of fittings.
In conjunction with the other parts of the ISO 16486 series, this document is applicable to PA-U fittings, their joints, joints with components of PA-U and joints with mechanical fittings of other materials, and to the following fitting types:
—     fusion fittings (electrofusion fittings and butt fusion fittings), and
—     transition fittings.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9080:2012(Main)
Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012)
SIST EN ISO 9080:2012

ISO 9080:2012 specifies a method for predicting the long-term hydrostatic strength of thermoplastics materials by statistical extrapolation. The method is applicable to all types of thermoplastics pipe at applicable temperatures. It was developed on the basis of test data from pipe systems.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 852:2010(Main)
Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Guidance on the interpretation of laboratory derived migration values
SIST-TP CEN/TR 852:2011

This Technical Report is applicable to plastics pipes, joints and fittings to be used for the transport of water intended for human consumption and raw water used for the manufacture of water intended for human consumption.
It gives guidance on:
a)   the number of successive migration periods to be carried out;
b)   how to interpret M values calculated from successive migration periods;
c)   a method for converting M values into values that reflect field use conditions;
d)   acceptance criteria for the duplicate M values obtained by testing in accordance with EN ISO 8795.

  • Technical report
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day