iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1447:1996

(Main)

Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure

Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure

This standard specifies a method for determining the long-term behaviour of glass-reinforced thermosetting plastics (GRP) pipes under internal hydrostatic pressure at a specified temperature. Note: For other internal or external environments the referring standard should specify any additional requirement.

Kunststoff-Rohrleitungssysteme - Rohre aus glasfaserverstärkten duroplastischen Kunststoffen (GFK) - Bestimmung der Langzeit-Widerstandsfähigkeit gegen Innendruck

Diese Norm legt ein Verfahren zur Bestimmung des Langzeit-Verhaltens von Rohren   aus glasfaserverstärkten duroplastischen Kunstoffen (GFK) unter hydrostatischem Innendruck bei einer festgelegten Temperatur fest. Anmerkung: Für andere inneren oder äußeren Umgebungsbedingungen sollte die verweisende Norm zusätzliche Anforderungen festlegen.

Systèmes de canalisations en plastiques - Tubes en plastiques thermodurcissables renforcés de verre (PRV) - Détermination de la résistance à long terme à la pression interne

Cette norme spécifie une méthode pour la détermination du comportement à long terme de tubes en plastiques thermodurcissables renforcés de verre (PRV) sous pression hydrostatique interne à une température spécifiée. Note: Pour d'autres milieux d'environnement, internes ou externes, la norme référence devrait indiquer toute exigence supplémentaire.

Cevni sistemi iz polimernih materialov - Cevi iz duromernih materialov, ojačenih s steklenimi vlakni (GRP) - Določanje dolgoročne odpornosti proti notranjemu tlaku

General Information

Status
Withdrawn
Publication Date
17-Sep-1996
Withdrawal Date
17-Mar-2009
ICS
23.040.20 - Plastics pipes
83.140.30 - Plastics pipes and fittings for non fluid use
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 14 - Systems of glass-reinforced thermosetting plastics for all applications - Polyester, epoxy and polyester resin based concrete
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
18-Mar-2009
Completion Date
18-Mar-2009
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
SIST EN 1447:1997 - Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure

Relations

Replaced By
EN 1447:2009 - Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure
Effective Date
08-Jun-2022

Buy Standard

EN 1447:1997EN 1447:1997
PreviousNext
Standard
EN 1447:1997
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoff-Rohrleitungssysteme - Rohre aus glasfaserverstärkten duroplastischen Kunststoffen (GFK) - Bestimmung der Langzeit-Widerstandsfähigkeit gegen InnendruckSystemes de canalisations en plastiques - Tubes en plastiques thermodurcissables renforcés de verre (PRV) - Détermination de la résistance a long terme a la pression internePlastics piping systems - Glass-reinforced thermos
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 9080:2012(Main)
Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012)
SIST EN ISO 9080:2012

ISO 9080:2012 specifies a method for predicting the long-term hydrostatic strength of thermoplastics materials by statistical extrapolation. The method is applicable to all types of thermoplastics pipe at applicable temperatures. It was developed on the basis of test data from pipe systems.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1394:1996(Main)
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength
SIST EN 1394:1997

This standard specifies six test methods for the determination of the apparent initial tensile strength in the circumferential direction per unit length of glass-reinforced thermosetting plastics (GRP) pipes. The burst test (method A) is suitable for all types and sizes of pipes. It is the preferred method for pipes up to and including DN 600.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1393:1996(Main)
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial longitudinal tensile properties
SIST EN 1393:1997

This standard specifies three test methods for determining the longitudinal tensile properties of pipes of glass-reinforced thermosetting plastics (GRP). The properties which can be determined are: - the longitudinal tensile strength; - the percentage ultimate elongation; - the longitudinal modulus of elasticity. Method A uses for the test piece(s) a longitudinal strip cut from a pipe. Method B uses a specified length of the full cross section of the pipe. Method C uses a notched plate cut from a pipe wall section.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9080:2012(Main)
Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012)
SIST EN ISO 9080:2012

ISO 9080:2012 specifies a method for predicting the long-term hydrostatic strength of thermoplastics materials by statistical extrapolation. The method is applicable to all types of thermoplastics pipe at applicable temperatures. It was developed on the basis of test data from pipe systems.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1394:1996(Main)
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength
SIST EN 1394:1997

This standard specifies six test methods for the determination of the apparent initial tensile strength in the circumferential direction per unit length of glass-reinforced thermosetting plastics (GRP) pipes. The burst test (method A) is suitable for all types and sizes of pipes. It is the preferred method for pipes up to and including DN 600.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1393:1996(Main)
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial longitudinal tensile properties
SIST EN 1393:1997

This standard specifies three test methods for determining the longitudinal tensile properties of pipes of glass-reinforced thermosetting plastics (GRP). The properties which can be determined are: - the longitudinal tensile strength; - the percentage ultimate elongation; - the longitudinal modulus of elasticity. Method A uses for the test piece(s) a longitudinal strip cut from a pipe. Method B uses a specified length of the full cross section of the pipe. Method C uses a notched plate cut from a pipe wall section.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3581:2023(Main)
Welding consumables - Covered electrodes for manual metal arc welding of stainless and heat-resisting steels - Classification (ISO 3581:2023)
SIST EN ISO 3581:2023

This document specifies requirements for classification of covered electrodes, based on the all-weld metal chemical composition, the type of electrode covering and other electrode properties, and the all-weld metal mechanical properties, in the as-welded or heat-treated conditions, for manual metal arc welding of stainless and heat-resisting steels.
This document is a combined standard providing for classification utilizing a system based upon classification according to nominal composition or utilizing a system based upon classification according to alloy type.
a)       Paragraphs and tables which carry the label “classification according to nominal composition-A” or “ISO 3581-A” are applicable only to products classified to that system.
b)       Paragraphs and tables which carry the label “classification according to alloy type-B” or “ISO 3581-B” are applicable only to products classified to that system.
c)        Paragraphs and tables which carry neither label are applicable to products classified according to either or both systems.
Annex B gives information on considerations on weld metal ferrite content.

  • Draft
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11363-1:2018/A1:2023(Amendment)
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Amendment 1 (ISO 11363-1:2018/Amd 1:2023)
SIST EN ISO 11363-1:2018/A1:2023
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4880:2023(Main)
Aerospace series - General technical specification for standard parts
kSIST FprEN 4880:2022
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18743:2015/A1:2023(Amendment)
Microbiology of the food chain - Detection of Trichinella larvae in meat by artificial digestion method - Amendment 1: Method validation studies and performance characteristics (ISO 18743:2015/Amd 1:2023)
SIST EN ISO 18743:2015/A1:2023
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day