EN ISO 6115:1996

SLOVENSKI STANDARD
SIST EN ISO 6115:2000
01-december-2000
Shipbuilding - Trawl winches (ISO 6115:1988)
Shipbuilding - Trawl winches (ISO 6115:1988)
Schiffbau - Fischnetzwinden (ISO 6115:1988)
Construction navale - Treuils de peche (ISO 6115:1988)
Ta slovenski standard je istoveten z: EN ISO 6115:1996
ICS:
47.020.40 Dvigalna oprema in oprema Lifting and cargo handling
za pretovor equipment
SIST EN ISO 6115:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 6115:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 6115:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 6115:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 6115:2000
ISO
INTERNATIONAL STANDARD
6115
Second edition
1988-11-01
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION
ORGANISATION INTERNATIONALE DE NORMALISATION
MEXAYHAPOfiHAfl OPTAHVl3AL(Mfl fl0 CTAHAAPTM3AlJMM
Shipbuilding - Trawl winches
Construction navafe - Treuils de @ehe
Reference number
*
ISO 6115 : 1988 (E)

---------------------- Page: 5 ----------------------

SIST EN ISO 6115:2000
ISO 6115:1988 (El
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of
national Standards bodies (ISO member bodies). The work of preparing International
Standards is normally carried out through ISO technical committees. Esch member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all
matter-s of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the ISO Council. They are approved in accordance with ISO procedures requiring at
least 75 % approval by the member bodies voting.
International Standard ISO 6115 was prepared by Technical Committee ISO/TC 8,
Shipbuilding and marine structures.
This second edition cancels and replaces the first edition (ISO 6115 : 1981) of which it
constitutes a minor revision.
Annex A forms an integral part of this International Standard; annexes B and C are
given for information only.
0 International Organkation for Standardkation, 1988
Printed in Switzerland

---------------------- Page: 6 ----------------------

SIST EN ISO 6115:2000
ISO 6115 : 1988 (E)
INTERNATIONAL STANDARD
Shipbuilding - Trawl winches
3 Definitions
1 Scope
For the purposes of this International Standard, the definitions
This International Standard specifies requirements and
given in ISO 3828 and the following definitions apply.
characteristics of Single-drum and double-drum trawl winches
with electric, electro-hydraulic, hydraulic diese1 or externally
powered drive.
31 nominal size: Drum load on the trawl rope drum, in
tonries, as stated in table 1, for a Single-drum trawl winch.
The winches are used for hauling-in, paying-out and holding
the trawl rope while fishing by means of trawling fishing gear.
NOTE - For a double-drum trawl winch, the nominal size corresponds
to twice the drum load stated in table 1.
When equipped with additional auxiliary drums, they may also
be used for auxiliary operations when hauling-in, paying-out
3.2 drum load: Maximum trawl rope tension, measured at
and emptying the trawl net.
the drum exit with a trawl rope being hauled-in at the nominal
Speed and being wound onto the appropriate nominal trawl
rope winding diameter of the drum.
2 Normative references 3.3 design torque: Driving torque available at the drum,
resulting from the drum load applied to the half-length rope
The following Standards contain provisions which, through nominal trawl rope winding diameter, for a Single-drum winch.
reference in this text, constitute provisions of this International
- For a double-drum winch, the design torque is twice the
Standard. At the time of publication, the editions indicated NOTE
design torque of a Single-drum winch.
were valid. All Standards are subject to revision, and Parties to
agreements based on this International Standard are encouraged
to investigate the possibility of applying the most recent
3.4 Nominal trawl rope winding diameter
editions of the Standards listed below. Members of IEC and ISO
maintain registers of currently valid International Standards.
3.4.1 winding diameter full-length rope: Diameter when
the whole design length of the rope has been wound onto the
ISO 2408 : 1985, Steel wire ropes for general purposes -
drum, i.e. diameter of the outermost layer of the rope.
Charac teris tics.
3.4.2 win
...