iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN 15015

(Main)

Plastics piping systems - Hot and cold water piping components - Requirements and test/assessment methods for pipes and fittings

Plastics piping systems - Hot and cold water piping components - Requirements and test/assessment methods for pipes and fittings

This European Standard specifies requirements for plastics pipes and fittings for hot and cold water installations.
It gives associated test/assessment methods.
This standard does not cover adhesives, joint sealings and gasket
It is intended to be used for distribution of hot and cold water and for heating systems inside buildings with the exception of water intended for human consumption.
NOTE    Products complying with this document may be used for the transport of water intended for human consumption if they comply with the relevant national, regional or local regulatory provisions applicable in place of use. Compliance of a product with this document does not confer a presumption of fitness of the product for the transport of water intended for human consumption within the meaning of the Directive 89/106/EEC.

Kunststoff-Rohrleitungssysteme - Bauteile für den Einsatz in Rohrleitungen für Warm- und Kaltwasser - Anforderungen und Prüf /Bewertungsverfahren für Rohre und Formstücke

Diese Europäische Norm legt Anforderungen an Rohre und Formstücke aus Kunststoff für die Warm- und Kaltwasserinstallation fest.
Sie enthält die zugehörigen Prüf-/Bewertungsverfahren.
Diese Norm gilt nicht für Klebstoffe, Abdichtungen von Rohrverbindungen und Dichtungen.
Sie ist vorgesehen für die Verteilung von Warm- und Kaltwasser sowie für Heizungsanlagen innerhalb von Gebäuden mit Ausnahme von Wasser für den menschlichen Gebrauch.
ANMERKUNG Produkte dürfen bei Übereinstimmung mit diesem Dokument für den Transport von Wasser für den menschlichen Gebrauch verwendet werden, sofern sie die entsprechenden am Einsatzort geltenden nationalen, regio-nalen oder örtlichen gesetzlichen Bestimmungen erfüllen. Die Übereinstimmung eines Produkts mit diesem Dokument stellt keine Annahme der Gebrauchstauglichkeit des Produkts für den Transport von Wasser für den menschlichen Gebrauch im Sinne der Richtlinie 89/106/EWG dar.

Systèmes de canalisations en plastique - Composants de canalisations pour eau chaude et froide non destinée à la consommation humaine - Exigences et méthodes d'essais/d'évaluation pour tubes et raccords

La présente Norme européenne spécifie les exigences relatives aux tubes et aux raccords en plastique destinés aux installations d’eau chaude et froide.
Elle indique les méthodes d’essais/d’évaluation associées.
La présente norme ne traite pas des adhésifs, des joints d’étanchéité et des garnitures de joints.
Elle est destinée à être utilisée pour la distribution d’eau chaude et froide et pour les systèmes de chauffage à l’intérieur des bâtiments, à l’exclusion de l’eau destinée à la consommation humaine.
NOTE   Les produits conformes au présent document peuvent être utilisés pour le transport de l’eau destinée à la consommation humaine à condition d’être conformes aux réglementations nationales, régionales ou locales applicables sur le lieu d’utilisation. La conformité d’un produit au présent document ne confère pas une présomption d’aptitude du produit pour le transport de l’eau destinée à la consommation humaine au sens de la Directive 89/106/CEE.

Cevni sistemi iz polimernih materialov - Cevne komponente za vročo in hladno vodo - Zahteve in preskusi/metode ocenjevanja za cevi in fitinge

General Information

Status
Not Published
Publication Date
02-Feb-2016
Withdrawal Date
02-Aug-2016
ICS
23.040.01 - Pipeline components and pipelines in general
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 30 - Pressure hENs
Current Stage
3098 - Decision to reject - Consensus building
Completion Date
10-Jun-2016
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
Mandate
M/131 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on pipes, tanks and ancillaries, not in contact with water intended for human consumption
Ref Project
oSIST prEN 15015:2014 - Plastics piping systems - Hot and cold water piping components - Requirements and test/assessment methods for pipes and fittings

Relations

Revises
EN 15015:2007 - Plastics piping systems - Systems for hot and cold water not intended for human consumption - Performance characteristics for pipes, fittings and their joints
Effective Date
19-Jan-2023

Buy Standard

prEN 15015:2014prEN 15015:2014
PreviousNext
Draft
prEN 15015:2014
English language
57 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 15015:2014
01-julij-2014
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY&HYQHNRPSRQHQWH]DYURþRLQKODGQR
YRGR=DKWHYHLQSUHVNXVLPHWRGHRFHQMHYDQMD]DFHYLLQILWLQJH
Plastics piping systems - Hot and cold water piping components - Requirements and
test/assessment methods for pipes and fittings
Kunststoff-Rohrleitungssysteme - Bauteile für den Einsatz in Rohrleitungen für Warm-
und Kaltwasser - Anforderungen und Prüf /Bewertungsverfahren für Rohre und
Formstücke
Systèmes de canalisations en plastique - Composants de canalisations pour eau chaude
et froide non destinée à la consommation humaine - Exigences et méthodes
d'essais/d'évaluation pour tubes et raccords
Ta slovenski standard je istoveten z: prEN 15015
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
oSIST prEN 15015:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15015:2014

---------------------- Page: 2 ----------------------
oSIST prEN 15015:2014

EUROPEAN STANDARD
DRAFT
prEN 15015
NORME EUROPÉENNE

EUROPÄISCHE NORM

April 2014
ICS 23.040.01 Will supersede EN 15015:2007
English Version
Plastics piping systems - Hot and cold water piping components
- Requirements and test/assessment methods for pipes and
fittings
Systèmes de canalisations en plastique - Composants de Kunststoff-Rohrleitungssysteme - Bauteile für den Einsatz
canalisations pour eau chaude et froide non destinée à la in Rohrleitungen für Warm- und Kaltwasser -
consommation humaine - Exigences et méthodes Anforderungen und Prüf /Bewertungsverfahren für Rohre
d'essais/d'évaluation pour tubes et raccords und Formstücke
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15015:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 15015:2014
prEN 15015:2014 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms, definitions and abbreviations .8
3.1 Terms and definitions .8
3.2 Abbreviations .8
4 Product characteristics .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TS 17152-3:2022/AC:2024(Corrigendum)
Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Boxes used for infiltration, attenuation and storage systems - Part 3: Assessment of conformity
SIST-TS CEN/TS 17152-3:2023/AC:2024

This document gives guidance for requirements for the assessment of conformity (AoC) of materials, compounds, formulations, products, and assemblies in accordance with the applicable part(s) of EN 17152 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   Annex B, Table B.1 contains a summary of tests for TT and surveillance monitoring.
In conjunction with EN 17152 1 (see European foreword) this document is applicable to boxes used for infiltration, attenuation and storage systems.

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1566-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1566-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulations, products, joints and assemblies in accordance with the applicable part of EN 1566 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1566 1 (see European foreword), this document is applicable to solid-wall piping systems made of chlorinated poly(vinyl chloride) (PVC C) intended to be used for or soil and waste discharge systems (low and high temperature):
-   inside buildings (application area code "B");
-   for both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1455-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1455-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulation, products, joints and assemblies in accordance with the applicable part of EN 1455 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1455-1 (see European foreword), this document is applicable to solid wall piping systems made of acrylonitrile-butadiene-styrene (ABS) intended to be used for soil and waste discharge (low and high temperature):
-   inside buildings (application area code "B");
-   both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1401-1:2019+A1:2023(Main + Amendment)
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1401-1:2019+A1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC U) piping systems in the field of non-pressure underground drainage and sewerage:
- buried in ground outside the building structure (application area code "U"), and
- both buried in ground, within the building structure and outside the building (application area code "UD").
NOTE 1   The intended use is reflected in the marking of products by "U" or "UD".
It also specifies the test parameters for the test methods referred to in this document.
NOTE 2   Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 13476-2 [1].
This document covers a range of nominal sizes, a range of pipes and fittings series and a range of stiffness classes and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to PVC U pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 16.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1566-1:2022(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1566-1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of chlorinated poly(vinyl chloride) (PVC-C) piping systems intended for soil and waste discharge (low and high temperature):
- inside buildings (application area code “B”);
- for both inside buildings and buried in ground within the building structure (application area code “BD”).
NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”.
NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.
NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.
NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements.
This document is applicable to PVC-C pipes and fittings and the system intended for the following purposes:
- ventilating part of the pipework in association with discharge applications;
- rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipe series and gives recommendations concerning colours.
NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1455-1:2022(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1455-1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) piping systems intended for soil and waste discharge applications (low and high temperature):
- inside buildings (application area code “B”);
- for both inside buildings and buried in ground within the building structure (application area code “BD”).
NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”.
NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.
NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.
NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements.
This document is also applicable to ABS and ASA pipes, fittings and the system intended for the following purposes:
- ventilating part of the pipework in association with discharge applications;
- rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17152-3:2022(Main)
Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Boxes used for infiltration, attenuation and storage systems - Part 3: Conformity assessment scheme
SIST-TS CEN/TS 17152-3:2023

This document gives guidance for requirements for the assessment of conformity (AoC) of materials, compounds, formulations, products, and assemblies in accordance with the applicable part(s) of EN 17152 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   Annex B, Table B.1 contains a summary of tests for TT and surveillance monitoring.
In conjunction with EN 17152 1 (see European foreword) this document is applicable to boxes used for infiltration, attenuation and storage systems.

  • Technical specification
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical specification
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15874-1:2013/A1:2022(Amendment)
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General - Amendment 1: Impact test (ISO 15874-1:2013/Amd 1:2022)
SIST EN ISO 15874-1:2013/A1:2022
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11295:2022(Main)
Plastics piping systems used for the rehabilitation of pipelines - Classification and overview of strategic, tactical and operational activities (ISO 11295:2022)
SIST EN ISO 11295:2022

This document specifies the steps of the overall process of pipeline rehabilitation, comprising:
—    information on strategic and tactical activities:
a) investigation and condition assessment of the existing pipeline;
b) pipeline rehabilitation planning.
—    information on and requirements for operational activities:
c) project specification;
d) applications of techniques;
e) documentation of the design and application process.
Definitions and classification of families of renovation and trenchless replacement techniques are provided, and their respective features described. Areas of application covered include underground drainage and sewerage networks and underground water and gas supply networks.
The following aspects are not covered by the scope of this document:
—    new construction provided as network extensions;
—    calculation methods to determine, for each viable technique, the characteristics of lining or replacement pipe material needed to secure the desired performance of the rehabilitated pipeline;
—    techniques providing non-structural pressure pipe liners;
—    techniques for local repair.
It is the responsibility of the designer to choose and design the renovation or trenchless replacement pipeline system.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1555-7:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
SIST-TS CEN/TS 1555-7:2022

This document gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 1555 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
This document gives recommendations that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001.
NOTE 1 If certification is involved, the certification and inspection body is preferably compliant with EN ISO/IEC 17065, EN IS0/IEC 17021 or EN ISO/IEC 17020, as applicable.
In conjunction with Parts 1 to 5 of EN 1555 (see Foreword), this document is applicable to polyethylene (PE) plastics piping systems for the supply of gaseous fuels. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 10 bar;
b) an operating temperature of 20 °C as reference temperature.
NOTE 2 For other operating temperatures, derating coefficients can be used; see EN 1555-5.

  • Technical specification
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day