EN 12952-5:2021
(Main)Water-tube boilers and auxiliary installations - Part 5: Workmanship and construction of pressure parts of the boiler
Water-tube boilers and auxiliary installations - Part 5: Workmanship and construction of pressure parts of the boiler
This European Standard specifies requirements for the workmanship and construction of water-tube boilers as defined in EN 12952-1.
Wasserrohrkessel und Anlagenkomponenten - Teil 5: Verarbeitung und Bauausführung für drucktragende Kesselteile
Chaudières à tubes d'eau et installations auxiliaires - Partie 5: Fabrication et construction des parties sous pression des chaudières
Vodocevni kotli in pomožne napeljave - 5. del: Izdelava in izvedba tlačno obremenjenih delov kotla
Ta evropski standard določa zahteve za izdelavo in izvedbo vodocevnih kotlov iz standarda EN 12952-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12952-5:2022
01-februar-2022
Nadomešča:
SIST EN 12952-5:2012
Vodocevni kotli in pomožne napeljave - 5. del: Izdelava in izvedba tlačno
obremenjenih delov kotla
Water-tube boilers and auxiliary installations - Part 5: Workmanship and construction of
pressure parts of the boiler
Wasserrohrkessel und Anlagenkomponenten - Teil 5: Verarbeitung und Bauausführung
für drucktragende Kesselteile
Chaudières à tubes d'eau et installations auxiliaires - Partie 5: Fabrication et construction
des parties sous pression des chaudières
Ta slovenski standard je istoveten z: EN 12952-5:2021
ICS:
27.060.30 Grelniki vode in prenosniki Boilers and heat exchangers
toplote
SIST EN 12952-5:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12952-5:2022
---------------------- Page: 2 ----------------------
SIST EN 12952-5:2022
EN 12952-5
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2021
EUROPÄISCHE NORM
ICS 27.040 Supersedes EN 12952-5:2011
English Version
Water-tube boilers and auxiliary installations - Part 5:
Workmanship and construction of pressure parts of the
boiler
Chaudières à tubes d'eau et installations auxiliaires - Wasserrohrkessel und Anlagenkomponenten - Teil 5:
Partie 5: Fabrication et construction des parties sous Verarbeitung und Bauausführung für drucktragende
pression des chaudières Kesselteile
This European Standard was approved by CEN on 1 November 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12952-5:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12952-5:2022
EN 12952-5:2021 (E)
Contents
European foreword . 8
1 Scope . 10
2 Normative references . 10
3 Terms and definitions . 12
4 Symbols and abbreviations . 12
5 General. 12
6 Pressure part . 13
6.1 Drums, headers and similar pressure parts . 13
6.1.1 Principles for manufacturing . 13
6.1.2 Manufacturing process for header ends . 13
6.1.3 Material for header ends . 13
6.2 Material identification . 13
6.3 Material marking .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.