Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs with specified grades and property classes (ISO 3506-1:2020)

This document specifies the mechanical and physical properties of bolts, screws and studs, with coarse pitch thread and fine pitch thread, made of corrosion-resistant stainless steels, when tested at the ambient temperature range of 10 °C to 35 °C. It specifies property classes in relation to austenitic, martensitic, ferritic and duplex (austenitic-ferritic) steel grades for fasteners.
The term "fasteners" is used in this document when bolts, screws and studs are considered all together.
ISO 3506‑6 provides general rules and additional technical information on suitable stainless steels and their properties.
Fasteners conforming to the requirements of this document are evaluated at the ambient temperature specified in paragraph 1. It is possible that they do not retain the specified mechanical and physical properties at elevated and/or lower temperatures.
NOTE 1  Fasteners conforming to the requirements of this document are used without restriction in applications ranging from ?20 °C to +150 °C; however, fasteners conforming to this document are also used for applications outside this range down to ?196 °C and up to +300 °C. For more details, see Annex A and ISO 3506‑6.
Outside the temperature range of ?20 °C to +150 °C, it is the responsibility of the user to determine the appropriate choice for a given application in consultation with an experienced fastener metallurgist and by taking into account e.g. stainless steel composition, duration of exposure at elevated or low temperature, the effect of the temperature on the fasteners mechanical properties and clamped parts, and the corrosive service environment of the bolted joint.
NOTE 2  ISO 3506‑5 is developed in order to assist in the selection of appropriate stainless steel grades and property classes intended for use at temperatures up to +800 °C.
This document applies to bolts, screws and studs:
—          with ISO metric thread in accordance with ISO 68‑1,
—          with diameter/pitch combinations in accordance with ISO 261 and ISO 262,
—          with coarse pitch thread M1,6 to M39, and fine pitch thread M8×1 to M39×3,
—          with thread tolerances in accordance with ISO 965‑1 and ISO 965‑2,
—          with specified property classes, and
—          of any shape.
Stainless steel grades and property classes can be used for sizes outside the diameter limits of this document (i.e. for d < 1,6 mm or d > 39 mm), provided that all applicable chemical, mechanical and physical requirements are met.
Certain bolts, screws and studs might not fulfil the tensile or torsional requirements of this document because of the geometry of their head or unthreaded shank, thus resulting in reduced loadability (e.g. when shear area in the head is less than the stress area in the thread; see 8.2.2).
This document does not apply to set screws and similar threaded fasteners not under tensile stress (see ISO 3506‑3).
It does not specify requirements for functional properties such as:
—          torque/clamp force properties,
—          shear strength,
—          fatigue resistance, or
—          weldability.

Mechanische Verbindungselemente - Mechanische Eigenschaften von Verbindungselementen aus korrosionsbeständigen nichtrostenden Stählen - Teil 1: Schrauben mit festgelegten Stahlsorten und Festigkeitsklassen (ISO 3506-1:2020)

Dieses Dokument legt die mechanischen und physikalischen Eigenschaften von Schrauben mit Regelgewinde und Feingewinde aus korrosionsbeständigen nichtrostenden Stählen bei Prüfung in einem Umgebungs¬temperaturbereich von 10 °C bis 35 °C fest. Es legt Festigkeitsklassen in Bezug auf austenitische, martensi¬tische, ferritische Stahlsorten sowie austenitisch-ferritische Duplex-Stahlsorten für Verbindungselemente fest.
Der Begriff „Verbindungselemente“ (en: fasteners) wird in diesem Dokument verwendet, wenn „Schrauben mit Schaft“ (en: bolts) oder „Schrauben mit Gewinde bis Kopf“ (en: screws) sowie „Stiftschrauben oder Gewindebolzen“ (en: studs) als Gesamtheit angesprochen werden.
In ISO 3506 6 werden allgemeine Regeln und zusätzliche technische Angaben zu geeigneten nichtrostenden Stählen und ihren Eigenschaften bereitgestellt.
Verbindungselemente, die den Anforderungen dieses Dokuments entsprechen, werden bei der in Absatz 1 angegebenen Umgebungstemperatur bewertet. Eventuell ändern sich die festgelegten mechanischen und physikalischen Eigenschaften bei höheren und/oder niedrigeren Temperaturen.
ANMERKUNG 1 Verbindungselemente, die den Anforderungen dieses Dokuments entsprechen, werden ohne Einschränkung für Anwendungen im Bereich zwischen −20 °C und +150 °C eingesetzt; Verbindungselemente, die diesem Dokument entsprechen, werden jedoch auch für die Anwendung außerhalb dieses Bereiches von −196 °C und bis zu +300 °C eingesetzt. Für weiterführende Einzelheiten siehe Anhang A und ISO 3506 6.
Außerhalb des Temperaturbereichs von −20 °C bis +150 °C liegt es in der Verantwortlichkeit des An-wenders – unter Hinzuziehung eines erfahrenen Metallurgen für Verbindungselemente – eine geeignete Wahl für eine bestimmte Anwendung zu treffen, um z. B. die Zusammensetzung des nichtrostenden Stahls, die Dauer der Beanspruchung bei einer hohen oder niedrigen Temperatur, die Auswirkung der Temperatur auf die mechanischen Eigenschaften der Verbindungselemente und eingespannten Teile und die korrosive Einsatz¬umgebung der Schraubenverbindung zu berücksichtigt.
ANMERKUNG 2 ISO 3506 5 wird erarbeitet, um die Auswahl geeigneter Sorten nichtrostender Stähle und Festigkeits-klassen zu unterstützen, die für die Anwendung bei hohen Temperaturen bis +800 °C vorgesehen sind.
Dieses Dokument gilt für Schrauben:
- mit metrischem ISO Gewinde nach ISO 68 1;
- mit Durchmesser-Steigungs-Kombinationen nach ISO 261 und ISO 262;
- mit Regelgewinde M1,6 bis M39 und Feingewinde M8×1 bis M39×3;
- mit Gewindetoleranzen nach ISO 965 1 und ISO 965 2;
- mit festgelegten Festigkeitsklassen; und
- jeglicher Form.
Sorten nichtrostender Stähle und Festigkeitsklassen können auch für Größen außerhalb der in diesem Doku¬ment festgelegten Grenzen für Durchmesser (d. h. bei d < 1,6 mm oder d > 39 mm) verwendet werden, vorausgesetzt, alle geltenden chemischen, mechanischen und physikalischen Anforderungen werden erfüllt.
Aufgrund der Geometrie ihres Kopfes oder gewindefreien Schaftes, die zu einer reduzierten Belastbarkeit führt, (z. B. wenn die Scherfläche im Kopf gegenüber dem Spannungsquerschnitt im Gewinde verkleinert ist, siehe 8.2.2), erfüllen bestimmte Schrauben möglicherweise nicht die in diesem Dokument festgelegten Anforderungen an die Belastbarkeit unter Zug oder Torsion.
Dieses Dokument gilt nicht für Gewindestifte und ähnliche nicht auf Zug beanspruchte Verbindungselemente mit Gewinde (siehe ISO 3506 3).
Es legt keine Anforderungen an Funktionseigenschaften fest, wie:
- Drehmoment/Vorspannkraft-Eigenschaften;
- Scherfestigkeit;
- Dauerfestigkeit; oder
- Schweißbarkeit.

Fixations - Caractéristiques mécaniques des fixations en acier inoxydable résistant à la corrosion - Partie 1: Vis, goujons et tiges filetées de grades et classes de qualité spécifiés (ISO 3506-1:2020)

Le présent document spécifie les caractéristiques mécaniques et physiques des vis, goujons et tiges filetées, à filetage à pas gros et à filetage à pas fin, en aciers inoxydables résistant à la corrosion, lorsque soumis à essai dans la plage de température ambiante de 10 °C à 35 °C. Il spécifie les classes de qualité en fonction des grades d'aciers inoxydables austénitiques, martensitiques, ferritiques et duplex (austéno-ferritiques) pour les fixations.
Le terme «fixation» est utilisé dans le présent document lorsque les vis, goujons et tiges filetées sont considérés dans leur ensemble.
L'ISO 3506‑6 fournit des règles générales et des informations techniques supplémentaires sur les aciers inoxydables appropriés ainsi que leurs propriétés.
Les fixations conformes aux exigences du présent document sont évaluées dans la plage de température ambiante spécifiée dans l'alinéa 1. Elles peuvent ne pas conserver les caractéristiques mécaniques et physiques spécifiées à des températures élevées et/ou basses.
NOTE 1    Les fixations conformes aux exigences du présent document sont utilisées sans restriction pour des applications dans la plage de ? 20 °C à + 150 °C; cependant, les fixations conformes au présent document sont également utilisées pour des applications en dehors de cette plage, en températures négatives jusqu'à ? 196 °C et en températures élevées jusqu'à + 300 °C. Pour d'avantage d'explications, voir l'Annexe A et l'ISO 3506‑6.
En dehors de la plage de température de ? 20 °C à + 150 °C , il est de la responsabilité de l'utilisateur de déterminer le choix approprié pour une application donnée en concertation avec un métallurgiste expérimenté en fixations et en prenant en considération plusieurs facteurs, par exemple la composition de l'acier inoxydable, la durée d'exposition à température élevée ou basse, l'effet de la température sur les caractéristiques mécaniques des fixations et des pièces assemblées, ainsi que l'environnement corrosif d'utilisation de l'assemblage vissé.
NOTE 2    L'ISO 3506‑5 est développée afin d'aider à la sélection des grades d'aciers inoxydables et des classes de qualité appropriées destinés à être utilisés à des températures jusqu'à + 800 °C.
Le présent document s'applique aux vis, goujons et tiges filetées:
—          à filetage métrique ISO conforme à l'ISO 68‑1;
—          de combinaisons diamètre/pas, conformes à l'ISO 261 et à l'ISO 262;
—          de filetage M1,6 à M39 pour les pas gros, et de filetage M8×1 à M39×3 pour les pas fins;
—          de tolérances de filetage conformes à l'ISO 965‑1 et à l'ISO 965‑2;
—          de classes de qualité spécifiées; et
—          de forme quelconque.
Les grades d'aciers inoxydales et classes de qualité peuvent être utilisés pour des dimensions en dehors des limites de diamètres du présent document (c'est-à-dire pour d < 1,6 mm ou d > 39 mm), à condition que toutes les exigences chimiques, mécaniques et physiques applicables soient satisfaites.
Certaines vis, goujons et tiges filetées peuvent ne pas satisfaire aux exigences de la résistance à la traction ou à la torsion du présent document en raison de la géométrie de leur tête ou de leur partie lisse (tige), ce qui a pour conséquence une capacité de charge réduite (par exemple lorsque la section cisaillée dans la tête est inférieure à la section résistante dans le filetage, voir 8.2.2).
Le présent document ne s'applique pas aux vis sans tête et fixations filetées similaires non soumises à des contraintes de trac

Vezni elementi - Mehanske lastnosti veznih elementov iz korozijsko odpornega nerjavnega jekla - 1. del: Vijaki z matico, vijaki in zatični vijaki z določenimi razredi in razredi trdnosti (ISO 3506-1:2020)

General Information

Status
Published
Publication Date
14-Apr-2020
Withdrawal Date
30-Oct-2020
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
15-Apr-2020
Completion Date
15-Apr-2020

Relations

Buy Standard

Standard
EN ISO 3506-1:2020
English language
47 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN ISO 3506-1:2020
English language
47 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 3506-1:2018
English language
43 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 3506-1:2020
01-julij-2020
Nadomešča:
SIST EN ISO 3506-1:2011
Vezni elementi - Mehanske lastnosti veznih elementov iz korozijsko odpornega
nerjavnega jekla - 1. del: Vijaki z matico, vijaki in zatični vijaki z določenimi razredi
in razredi trdnosti (ISO 3506-1:2020)
Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part
1: Bolts, screws and studs with specified grades and property classes (ISO 3506-1:2020)
Mechanische Eigenschaften von Verbindungselementen aus korrosionsbeständigen
nichtrostenden Stählen - Teil 1: Schrauben mit festgelegten Festigkeitsklassen -
Regelgewinde und Feingewinde (ISO 3506-1:2020)
Caractéristiques mécaniques des fixations en acier inoxydable résistant à la corrosion -
Partie 1: Vis, goujons et tiges filetées de classes de qualité spécifiées - Filetage à pas
gros et filetage à pas fin (ISO 3506-1:2020)
Ta slovenski standard je istoveten z: EN ISO 3506-1:2020
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 3506-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 3506-1:2020

---------------------- Page: 2 ----------------------
SIST EN ISO 3506-1:2020


EN ISO 3506-1
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2020
EUROPÄISCHE NORM
ICS 21.060.10 Supersedes EN ISO 3506-1:2009
English Version

Fasteners - Mechanical properties of corrosion-resistant
stainless steel fasteners - Part 1: Bolts, screws and studs
with specified grades and property classes (ISO 3506-
1:2020)
Fixations - Caractéristiques mécaniques des fixations Mechanische Verbindungselemente - Mechanische
en acier inoxydable résistant à la corrosion - Partie 1: Eigenschaften von Verbindungselementen aus
Vis, goujons et tiges filetées de grades et classes de korrosionsbeständigen nichtrostenden Stählen - Teil 1:
qualité spécifiés (ISO 3506-1:2020) Schrauben mit festgelegten Stahlsorten und
Festigkeitsklassen (ISO 3506-1:2020)
This European Standard was approved by CEN on 28 March 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3506-1:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 3506-1:2020
EN ISO 3506-1:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 3506-1:2020
EN ISO 3506-1:2020 (E)
European foreword
This document (EN ISO 3506-1:2020) has been prepared by Technical Committee ISO/TC 2 "Fasteners"
in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by
BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2020, and conflicting national standards shall
be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3506-1:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, H
...

SLOVENSKI STANDARD
SIST EN ISO 3506-1:2020
01-julij-2020
Nadomešča:
SIST EN ISO 3506-1:2011
Vezni elementi - Mehanske lastnosti veznih elementov iz korozijsko odpornega
nerjavnega jekla - 1. del: Vijaki z matico, vijaki in zatični vijaki z določenimi razredi
in razredi trdnosti (ISO 3506-1:2020)
Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part
1: Bolts, screws and studs with specified grades and property classes (ISO 3506-1:2020)
Mechanische Eigenschaften von Verbindungselementen aus korrosionsbeständigen
nichtrostenden Stählen - Teil 1: Schrauben mit festgelegten Festigkeitsklassen -
Regelgewinde und Feingewinde (ISO 3506-1:2020)
Caractéristiques mécaniques des fixations en acier inoxydable résistant à la corrosion -
Partie 1: Vis, goujons et tiges filetées de classes de qualité spécifiées - Filetage à pas
gros et filetage à pas fin (ISO 3506-1:2020)
Ta slovenski standard je istoveten z: EN ISO 3506-1:2020
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
77.140.20 Visokokakovostna jekla Stainless steels
SIST EN ISO 3506-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 3506-1:2020

---------------------- Page: 2 ----------------------
SIST EN ISO 3506-1:2020


EN ISO 3506-1
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2020
EUROPÄISCHE NORM
ICS 21.060.10 Supersedes EN ISO 3506-1:2009
English Version

Fasteners - Mechanical properties of corrosion-resistant
stainless steel fasteners - Part 1: Bolts, screws and studs
with specified grades and property classes (ISO 3506-
1:2020)
Fixations - Caractéristiques mécaniques des fixations Mechanische Verbindungselemente - Mechanische
en acier inoxydable résistant à la corrosion - Partie 1: Eigenschaften von Verbindungselementen aus
Vis, goujons et tiges filetées de grades et classes de korrosionsbeständigen nichtrostenden Stählen - Teil 1:
qualité spécifiés (ISO 3506-1:2020) Schrauben mit festgelegten Stahlsorten und
Festigkeitsklassen (ISO 3506-1:2020)
This European Standard was approved by CEN on 28 March 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3506-1:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 3506-1:2020
EN ISO 3506-1:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 3506-1:2020
EN ISO 3506-1:2020 (E)
European foreword
This document (EN ISO 3506-1:2020) has been prepared by Technical Committee ISO/TC 2 "Fasteners"
in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by
BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2020, and conflicting national standards shall
be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3506-1:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Den
...

SLOVENSKI STANDARD
oSIST prEN ISO 3506-1:2018
01-marec-2018
Mehanske lastnosti veznih elementov iz nerjavnega jekla - 1. del: Vijaki s
specificiranim trdnostnim razredom - Grobi in fini navoj (ISO/DIS 3506-1:2018)
Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts,
screws and studs with specified property classes - Coarse pitch thread and fine pitch
thread (ISO/DIS 3506-1:2018)
Mechanische Eigenschaften von Verbindungselementen aus korrosionsbeständigen
nichtrostenden Stählen - Teil 1: Schrauben mit festgelegten Festigkeitsklassen -
Regelgewinde und Feingewinde (ISO/DIS 3506-1:2018)
Caractéristiques mécaniques des fixations en acier inoxydable résistant à la corrosion -
Partie 1: Vis, goujons et tiges filetées de classes de qualité spécifiées - Filetage à pas
gros et filetage à pas fin (ISO/DIS 3506-1:2018)
Ta slovenski standard je istoveten z: prEN ISO 3506-1
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
oSIST prEN ISO 3506-1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 3506-1:2018

---------------------- Page: 2 ----------------------
oSIST prEN ISO 3506-1:2018
DRAFT INTERNATIONAL STANDARD
ISO/DIS 3506-1
ISO/TC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
2018-01-09 2018-04-03
Mechanical properties of corrosion-resistant stainless
steel fasteners —
Part 1:
Bolts, screws and studs with specified property classes —
Coarse pitch thread and fine pitch thread
Caractéristiques mécaniques des fixations en acier inoxydable résistant à la corrosion —
Partie 1: Vis, goujons et tiges filetées de classes de qualité spécifiées — Filetage à pas gros et filetage à pas fin
ICS: 21.060.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 3506-1:2018(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2018

---------------------- Page: 3 ----------------------
oSIST prEN ISO 3506-1:2018
ISO/DIS 3506-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2018 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 3506-1:2018
ISO/DIS 3506-1:2018(E)

Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Symbols . 3
5 Designation system for stainless steel grades and property classes .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.