EN ISO 10256-2:2018
(Main)Protective equipment for use in ice hockey - Part 2: Head protection for skaters (ISO 10256-2:2016)
Protective equipment for use in ice hockey - Part 2: Head protection for skaters (ISO 10256-2:2016)
ISO 10256-2:2016 specifies performance requirements and test methods for head protectors for use in ice hockey and is intended to be read in conjunction with ISO 10256‑1.
Requirements and the corresponding test methods, where appropriate, are given for the following:
a) construction and protected area;
b) shock absorption;
c) penetration;
d) retention system properties;
e) field of vision;
f) marking and information.
ISO 10256-2:2016 applies to head protectors worn by
- players other than goalkeepers, and
- certain functionaries (e.g. referees).
NOTE 1 The requirements of a Clause take precedent over a figure.
NOTE 2 The intent of this part of ISO 10256 is to reduce the risk of injury to the head without compromising the form or appeal of the game.
Schutzausrüstung zum Gebrauch beim Eishockey - Teil 2: Kopfschutz für Eisläufer (ISO 10256-2:2016)
Dieser Teil der ISO 10256 legt Leistungsanforderungen und Prüfverfahren für Kopfschützer zum Gebrauch beim Eishockey fest und ist vorgesehen, in Verbindung mit ISO 10256 1 gelesen zu werden.
Anforderungen und entsprechende Prüfverfahren, wo anwendbar, sind für folgende Punkte festgelegt:
a) Konstruktion und geschützter Bereich;
b) Stoßdämpfung;
c) Durchdringung;
d) Eigenschaften der Trageeinrichtung;
e) Sichtfeld;
f) Kennzeichnung und Information.
Dieser Teil der ISO 10256 gilt für Kopfschützer, die von
— Spielern, ausgenommen Torwarte, und
— bestimmten Funktionären (z. B. Schiedsrichter) getragen werden.
ANMERKUNG 1 Die in einem Abschnitt angegebenen Anforderungen haben Vorrang vor einem Bild.
ANMERKUNG 2 Der Zweck dieses Teils der ISO 10256 ist die Verringerung des Risikos von Kopfverletzungen, ohne die Form oder die Attraktivität des Spiels zu beeinflussen.
Équipements de protection destinés à être utilisés en hockey sur glace - Partie 2: Protections de tête pour les skateurs (ISO 10256-2:2016)
ISO 10256-2:2016 spécifie les exigences de performance et les méthodes d'essai applicables aux protections de tête destinées à être utilisées en hockey sur glace. Elle doit être lue en complément de l'ISO 10256‑1.
Elle établit, s'il y a lieu, des exigences et les méthodes d'essai correspondantes pour les aspects suivants:
a) fabrication et zone protégée;
b) absorption des chocs;
c) pénétration;
d) propriétés du système de rétention;
e) champ de vision;
f) marquage et informations.
ISO 10256-2:2016 s'applique aux protections de tête utilisées par:
- les joueurs (à l'exception des gardiens de but); et
- certaines autorités (par exemple, les arbitres).
NOTE 1 Les exigences d'un article prévalent sur celles d'une figure.
NOTE 2 L'objectif de la présente partie de l'ISO 10256 est de réduire le risque de blessure à la tête sans compromettre pour autant l'aspect ou l'attrait même du jeu.
Varovalna oprema za uporabo pri hokeju na ledu - 2. del: Zaščita glave za drsalce (ISO 10256-2:2016)
Ta mednarodni standard določa zahteve glede učinkovitosti in preskusne metode za ščitnike za glavo za uporabo pri hokeju na ledu, uporabljati pa ga je treba skupaj s standardom ISO 10256-1. Opomba 1: Zahteve točke imajo prednost pred številsko vrednostjo. Opomba 2: Namen tega mednarodnega standarda je zmanjšati tveganje za poškodbe glave brez vpliva na način ali privlačnost igre. Opomba 3: Hokej na ledu je šport, ki vključuje tveganja za poškodbe. Ta mednarodni standard je namenjen le čeladam, ki se uporabljajo pri hokeju na ledu. Čelade za hokej na ledu ne zagotavljajo nobene zaščite pred poškodbami vratu ali hrbtenice. V skladu s tem mednarodnim standardom lahko pride do hudih poškodb glave, možganov ali hrbtenice oziroma paralize ali smrti navkljub uporabi čelade za hokej na ledu. Zahteve in ustrezne preskusne metode veljajo (kjer je to primerno) za:
a) izdelavo in pokritost; b) ublažitev udarcev;
c) prepustnost; d) lastnosti zadrževalnih sistemov; e) vidno polje; f) označevanje in podatke. Ta mednarodni standard se uporablja za ščitnike za glavo, ki jih uporabljajo:
a) igralci, ki niso vratarji; in
b) nekateri funkcionarji (npr. sodniki).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10256-2:2018
01-junij-2018
9DURYDOQDRSUHPD]DXSRUDERSULKRNHMXQDOHGXGHO =DãþLWDJODYH]DGUVDOFH
,62
Protective equipment for use in ice hockey - Part 2: Head protection for skaters (ISO
10256-2:2016)
Schutzausrüstung zum Gebrauch beim Eishockey - Teil 2: Kopfschutz für Eisläufer (ISO
10256-2:2016)
Équipements de protection destinés à être utilisés en hockey sur glace - Partie 2:
Protections de tête pour les skateurs (ISO 10256-2:2016)
Ta slovenski standard je istoveten z: EN ISO 10256-2:2018
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
97.220.20 Oprema za zimske športe Winter sports equipment
SIST EN ISO 10256-2:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10256-2:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 10256-2:2018
EN ISO 10256-2
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2018
EUROPÄISCHE NORM
ICS 97.220.20; 13.340.20
English Version
Protective equipment for use in ice hockey - Part 2: Head
protection for skaters (ISO 10256-2:2016)
Équipements de protection destinés à être utilisés en Schutzausrüstung zum Gebrauch beim Eishockey - Teil
hockey sur glace - Partie 2: Protections de tête pour les 2: Kopfschutz für Eisläufer (ISO 10256-2:2016)
skateurs (ISO 10256-2:2016)
This European Standard was approved by CEN on 17 September 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10256-2:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10256-2:2018
EN ISO 10256-2:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10256-2:2018
EN ISO 10256-2:2018 (E)
European foreword
This document (EN ISO 10256-2:2018) has been prepared by Technical Committee ISO/TC 83 "Sports
and other recreational facilities and equipment" in collaboration with Technical Committee
CEN/TC 158 “Head protection” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2018, and conflicting national standards shall
be withdrawn at the latest by October 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10256-2:2016 has been approved by CEN as EN ISO 10256-2:2018 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10256-2:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 10256-2:2018
INTERNATIONAL ISO
STANDARD 10256-2
First edition
2016-12-01
P
...
SLOVENSKI STANDARD
oSIST prEN ISO 10256-2:2015
01-september-2015
9DURYDOQDRSUHPD]DXSRUDERSULKRNHMXQDOHGXGHO =DãþLWDJODYH]DGUVDOFH
,62',6
Protective equipment for use in ice hockey - Part 2: Head protection for skaters (ISO/DIS
10256-2:2015)
Schutzausrüstung zur Benutzung beim Eishockey - Teil 2: Kopfschutz für Eisläufer
(ISO/DIS 10256-2:2015)
Protections de tête et de visage destinées à être utilisées en hockey sur glace - Partie 2:
Protecteurs de tête pour des joueurs de hockey sur glace (ISO/DIS 10256-2:2015)
Ta slovenski standard je istoveten z: prEN ISO 10256-2
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
97.220.20 Oprema za zimske športe Winter sports equipment
oSIST prEN ISO 10256-2:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 10256-2:2015
---------------------- Page: 2 ----------------------
oSIST prEN ISO 10256-2:2015
DRAFT INTERNATIONAL STANDARD
ISO/DIS 10256-2
ISO/TC 83/SC 5 Secretariat: SCC
Voting begins on: Voting terminates on:
2015-07-09 2015-10-09
Protective equipment for use in ice hockey —
Part 2:
Head protection for skaters
Protections de tête et de visage destinées à être utilisées en hockey sur glace
ICS: 13.340.20; 97.220.20
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 10256-2:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015
---------------------- Page: 3 ----------------------
oSIST prEN ISO 10256-2:2015
ISO/DIS 10256-2:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 10256-2:2015
Contents Page
Foreword . v
Introduction . vi
Protective equipment for use in ice hockey – Part 2: Head protection for skaters . 1
1 Scope . 1
2 Normative references . 1
3 Definitions . 2
4 Requirements . 4
4.1 Innocuousness . 4
4.2 Ergonomics .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.