2017/1369 - Regulation (EU) 2017/1369 of the European Parliament and of the Council of 4 July 2017 setting a framework for energy labelling and repealing Directive 2010/30/EU

IEC 62512:2012 provides a globally applicable and agreed method to test the washing and drying function of washer-dryers. Although this standard is based on IEC 61121:2012 on tumble dryers and IEC 60456:2010 on clothes washers, it specifies the conditions needed to test the combined function of washing and drying. The main elements of this standard are:   - the definition of the loads to be tested in continuous and interrupted operation cycles;  - the method for testing automatic and not automatic operation of the drying cycles;  - the way to handle the load for interrupted operation cycles;  - the correction to be applied to test results for continuous and interrupted operation cycles.

This Technical Specification provides a measurement and evaluation method for the determination of the representative maximum temperature reached inside the base load during the washing cycle of a washing machine or washer-dryer.
The mean maximum temperature within the base load is measured with three temperature sensors, which are attached to towels and/or pillowcases placed in different, representative locations inside the drum.
This Technical Specification does not provide a method for measuring a temperature for the evaluation of hygiene performance.

IEC 60704-2-4:2011 These particular requirements apply to single unit electrical washing machines and the washing and spinning function of combined appliances for household and similar use and to spin extractors for household and similar use. This third edition cancels and replaces the second edition (2001). Main changes are:  - measurement uncertainty and standard deviations are taken into account,  - definitions of standard test load and standard test program are modified,  - test enclosure was replaced by common test enclosure defined in Part 1 and  - information to be reported is modified.   This publication is to be read in conjunction with IEC 60704-1:2010.

2019-12-24: decision to skip FV taken by TC - mail from TC 2019-12-23

IEC 60704-2-4:2011 These particular requirements apply to single unit electrical washing machines and the washing and spinning function of combined appliances for household and similar use and to spin extractors for household and similar use. This third edition cancels and replaces the second edition (2001). Main changes are: - measurement uncertainty and standard deviations are taken into account, - definitions of standard test load and standard test program are modified, - test enclosure was replaced by common test enclosure defined in Part 1 and - information to be reported is modified. This publication is to be read in conjunction with  IEC 60704-1:2010.

2019-12-24: decision to skip FV taken by TC - mail from TC 2019-12-23

This document provides a measurement and evaluation method for the determination of the representative maximum temperature reached inside the base load during the washing cycle of a washing machine or washer-dryer. The mean maximum temperature within the base load is measured with three temperature sensors, which are attached to towels and/or pillowcases placed in different, representative locations inside the drum. This document does not provide a method for measuring a temperature for the evaluation of hygiene performance.

IEC 62512:2012 provides a globally applicable and agreed method to test the washing and drying function of washer-dryers. Although this standard is based on IEC 61121:2012 on tumble dryers and IEC 60456:2010 on clothes washers, it specifies the conditions needed to test the combined function of washing and drying. The main elements of this standard are: - the definition of the loads to be tested in continuous and interrupted operation cycles; - the method for testing automatic and not automatic operation of the drying cycles; - the way to handle the load for interrupted operation cycles; - the correction to be applied to test results for continuous and interrupted operation cycles.

This International Standard is applicable for measurements of the performance of dry vacuum cleaners for household use in or under conditions similar to those in households.
The purpose of this standard is to specify essential performance characteristics of dry vacuum cleaners being of interest to the users and to describe methods for measuring these characteristics.

This International Standard is applicable for measurements of the performance of dry vacuum cleaners for household use in or under conditions similar to those in households. The purpose of this standard is to specify essential performance characteristics of dry vacuum cleaners being of interest to the users and to describe methods for measuring these characteristics.